Votes - 4, Average rating: 4.3
(
)
)
|
manual abstract
Fig 1. Kit Contents (case not shown). Initial Charging The batteries in your new Cordless Screwdriver/Flashlight Kit will not be fully charged when you receive it. To maximize the storage capacity of the be completely discharged (turn and screwdriver on and let until the batteries discharge), then recharge for 10-12 hours. For optimal life span, completely discharge the battery after every use. Follow the instructions below to charge your battery NOTE: The battery does not need to be removed from the tool in order to be charged. 1. Plug the adapter into an appropriate 110/120V outlet. 2. Plug the other end of wire with the pin plug into the receptacle on the base of the Screwdriver or Flashlight battery pack (See Figure 2) . 3. Let the battery charge for 10-12 hours. This will give the battery a full charge. DO NOT let the battery charge for more than 12 hours. 4. When charging is complete, unplug the pin plug from the battery pack, and unplug the adapter from the wall outlet. The accessory should be ready to use. Fig 2. Plugging charger into battery. -6 G8592 3.6V Cordless Screwdriver/Flashlight OPERATION Inserting and Removing Drivers and Sockets: The hex end of the screwdriver bits fit into the hex opening on the end of the cordless driver. The bits can be inserted directly into the tool, or if additional extension is required, you can insert the bit extender first, then mount the bit on the end of the extension (See Figure 3). When using the supplied sockets you will need to use the square drive adapter which is included. You can easily distinguish this from the other drivers by the spring loaded detent ball on the square end. This helps to lock the socket into place on the end of the driver. Attach the socket to the adapter, then insert the adapter into the end of the driver tool. Torque Setting Turn the torque setting dial to the desired torque setting (See Figure 3) . Line up the number on the torque dial with the small arrow embossed on the left hand side of the case. Torque setting “1” has the highest torque, setting “6” the least. Use only the necessary amount of torque to avoid damaging the material you are driving into or the tool. The driver has a maximum speed of 150 RPM. Torque Setting Dial Fig 3. Using bit extension. G8592 3.6V Cordless Screwdriver/Flashlight -7 OPERATION Handle Position and The driver and flashlight are both the center to adjust to different types use. Adjust the angle to whatever is comfortable for the job to be done (See Figure 4.) Fwd/Rev Switch Lock Switch Fig 4. Positioning the handle and switch location. The driver has a two position rocker switch with forward and reverse. If you want to tighten a screw, push on the top of the switch to drive clockwise. To operate counterclockwise, push the bottom portion of the switch. There is also a locking switch just above the forward/reverse switch. This allows you to lock the tool to prevent accidental use of the tool. You should always use the LOCK position when placing, removing or adjusting bits or when removing the battery. The flashlight has only a slider ON/Off switch on the top of the case. Removing Battery The battery can be removed by on the two circular depressions at the of the handle and pulling away from the tool. When reinstalling the battery, be sure the elongated end of the battery is aligned with the slots on the inside of the compartment. The battery will lock into position when fully inserted. Operating this equipment has the potential to propel debris into the air which can cause eye injury. Always wear safety glasses or goggles when operating equipment. Be certain the safety glasses you wear meet the appropriate standards of the American National Standards Institute (ANSI). -8- G8592 3.6V Cordless Screwdriver/Flashlight OPERATING Operating Guides Avoid overloading the driver. Always use a driver which matches the fastener you are trying to drive. Do not apply excessive pressure to the driver while using. If the speed drops abnormally, decrease pressure immediately. If the driver stops abruptly or becomes blocked, release the switch at once. Ensure the safety of the workplace. Clear the work area of all parts and debris that may cause injury by flying objects. Securely fix the object to be fastened in a vise or otherwise clamp to avoid injury. Do not attempt to hold workpiece by hand. Inspect the driver before use. Run the driver before using to ensure all parts are running smoothly and there are no abnormal sounds or sparks. If any defect is found, have unit serviced. Know your worksite. Before driving fasteners, check behind walls for wires, other electrical hazards, or plumbing. Use accessories properly. Use the lowest possible torque setting when driving fasteners. This will increase the life span of the driving bit and prevent damage to the fastener. Maintenance Your cordless power tool will give of hours of operation time before ever needing service. The electrical components of this cordless drill are...