Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
Don't force a machine or attachment to do a job for which it was not designed. . USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your machine will draw. An undersized cord will cause a drop in the line voltage resulting in power loss and overheating. Ifindoubt,usethenextheaviergauge. Remember,thesmallerthegaugenumber,the heavier the cord. . WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slipfootwear is recommended. Wear protective hair covering to contain long hair. . ALWAYS USE SAFETY GLASSES. Also use face or dust masks if the cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses; they are not safety glasses. . DON'T OVERREACH. Keep proper footing and balance at all times. . MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for the best and safest performance. Follow instructions for lubricating and changing accessories. 1 . ALWAYS DISCONNECTTHEMACHINEFROMTHEPOWERSOURCEBEFORESERVICING. . . REDUCETHE RISKOF UNINTENTIONALSTARTING. Make sure the switch is in the off position before plugging in. . . NEVER STAND ON A MACHINE. Serious injury could occur if the machine tipped or if the drill bit is unintentionally contacted. . CHECK DAMAGED PARTS. Beforefurther useofthe machine,aguard orotherpartthat is damaged should be carefully checked to determine that it will qperate properly and perform its intended function -check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced. . NEVER LEAVE THE MACHINE RUNNING UNATTENDED. TURN POWER OFF. Don't leave the machine until it comes to a complete stop. Further reading on these and other safety information can be found in the publication Safety Requirements for the Construction, Care, and Use of Drilling, Milling, and Boring Machines (ANSI B11.8 1983) published by The American National Standards Institute. Order this publication from: The American National Standards Institute 1430 Broadway New York, New York 10018 ANSI B11.8-1983,Section5.1statesthat"itshallbetheresponsibilityoftheemployertoprovide,and ensure the use of, a guard, guarding device, awareness barrier, awareness device, or shield..." To assist employees and machine users in designing point of operation safeguarding for a specific machine application, the Occupational Safety and Health Administration offers a booklet titled Concepts and Techniques of Machine Safeguarding (O.S.H.A.publication#3067). Orderthispublicationfrom: The Publications Office -O.S.H.A. U.S. Department of Labor 200 Constitution Ave, NW Washington DC 20210 2 Electrical Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. Note: The JDP-20VS-1 is rated at 115/230V and comes pre-wired at 230V. The JDP-20VS-3 is rated at 230V and cannot be changed. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that isproperlyinstalledandgroundedinaccordancewithalllocalcodesandordinances. Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician. Improperconnectionoftheequipment-groundingconductorcanresultinariskofelectricshock. The conductor, with insulation having an outer surface that is green with or without yellow stripes, is the equipment-groundingconductor. Ifrepairorreplacementoftheelectriccordorplugisnecessary,donot connect the equipment-grounding conductor to a live terminal. Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. Use only three wire extension cords that havethree-pronggroundingplugsandthree-polereceptaclesthatacceptthetool'splug. Repair or replace a damaged or worn cord immediately. Important Information The JDP-20VS-1 comes pre-wired from the factory at 230V. It is strongly recommended that this drill press be operated at 230V. If, however, you decide to change the operating voltage to 115V, please be advised that the drill press may be hard to start when set at a higher R.P.M. When operating the drill press, lower the R.P.M. to the lowest setting before turning the machine off. This will make starting the machine easier. 115 Volt Operation Note: The JDP-20VS-1 is rated at 115/230V and comes pre-wired at 230V. The JDP-20VS-3 is rated at 230V only and cannot be changed. If 115V, single-phase operation is desired; the following instructions mus...