Votes - , Average rating:
(
)
)
Manafacture: Bosch
File size: 2.4 mb
File name: fb8443ef-44d5-4598-926e-01bcdaa17dd8.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
FIG. 4 Operating Instructions VARIABLE SPEED CONTROLLED The speed can be adjusted from the minimum TRIGGER SWITCH to maximum nameplate RPM by the pressure Your tool is equipped with a variable speed you apply to the trigger. Apply more pressure trigger switch. The tool can be turned "ON" or to increase the speed and release pressure to "OFF" by squeezing or releasing the trigger. decrease speed (Fig. 1). -9 BM 2610956386 07-08 7/1/08 1:25 PM Page 10 FORWARD/REVERSING LEVER & TRIGGER LOCK FIG. 5 !WARNING After tool use, lock trigger in “OFF” position to help prevent accidental starts and accidental discharge. Your tool is equipped with a forward/ reversing lever and trigger lock located above the trigger (Fig. 5). This lever was designed for changing rotation of the bit, and for locking the trigger in an “OFF” position. For forward rotation, (with chuck pointed away from you) move the lever to the far left. For reverse rotation move the lever to the far right. To activate trigger lock move lever to the center off position. !CAUTION Do not change direction of rotation until the tool comes to a complete stop. Shifting during rotation of the chuck can cause damage to the tool. GEAR SHIFTING Your tool is equipped with two separate gear ranges, low gear and high gear. Low gear provides high-torque and slower drilling speeds for heavy duty work or for driving screws. High gear provides faster speeds for drilling lighter work. To change speeds slide switch, to the high or low position (Fig. 6). ATTENTION: If your tool appears to be running, but the chuck will not turn, check to make sure the gear shifting switch is pushed fully into desired setting. ADJUSTABLE CLUTCH Your tool features 21 clutch settings. Output torque will increase as the clutch ring, is rotated from 1 to 20. The drill “ ” position will lock up the clutch to permit drilling and driving heavyduty work, and also enables bits to be changed quickly and easily in the keyless chuck (Fig. 6). BRAKE When the trigger switch is released it activates the brake to stop the chuck quickly. FIG. 6 ADJUSTABLE CLUTCH GEAR SHIFTER This is especially useful in the repetitive driving and removal of screws. BIT STORAGE AREA Your tool is equipped with a bit and storage area that is conveniently located in the handle base where it is always handy and unlikely to get lost or misplaced (Fig. 1). INSERTING AND RELEASING BATTERY PACK Set Forward/Reversing lever to the center (off Your tool is equipped with a secondary locking position). Slide charged battery pack into the latch to prevent the battery pack from housing until the battery pack locks into completely falling out of the handle, should it position (Fig. 7). become loose due to vibration. -10 BM 2610956386 07-08 7/1/08 1:25 PM Page 11 To remove the battery pack, press the battery pack release button and slide the battery pack forward. Press the battery pack release button again and slide the battery pack completely out of tool housing (Fig. 7). FIG. 7 IMPORTANT CHARGING NOTES 1. The charger was designed to fast charge the battery only when the battery temperature is between 32°F (0°C) and 113°F (45°C). If the battery pack is too hot or too cold, the charger will not fast charge the battery. (This may happen if the battery pack is hot from heavy use). When the battery temperature returns to between 32°F (0°C) and 113°F (45°C), the charger will automatically begin charging. 2. A substantial drop in operating time per charge may mean that the battery pack is nearing the end of its life and should be replaced. 3. Remember to unplug charger during storage period. 4. If battery does not charge properly: a. Check for voltage at outlet by plugging in some other electrical device. b. Check to see if outlet is connected to a light switch which turns power “off” when lights are turned off. c. Check battery pack terminals for dirt. Clean with cotton swab and alcohol if necessary. d. If you still do not get proper charging, take or send tool, battery pack and charger to your local Bosch Service Center. See “Tools, Electric” in the Yellow Pages for names and addresses. Note: Use of chargers or battery packs not sold by Bosch will void the warranty. CHARGER INDICATORS, SYMBOLS AND MEANING (Model BC630) If the indicator lights are “OFF”, the charger is not receiving power from power supply outlet. the battery pack is fully charged. If the green indicator light is “ON”, the charger is plugged in but the battery pack is not inserted, or If the green indicator light is “BLINKING”, the battery pack is being fast-charged. Fast-charging will automatically stop when the battery pack is fully charged. If the red indicator light is “ON”, the battery pack is too hot or cold for fast-charging. The charger will suitable temperature is reached. automatically switch to fast-charging once a If the red indicator light is “BLINKING”, the battery pack cannot accept a charge or the contacts of the charger or battery pack are contaminated. Clean the ...