Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
Home Theater Systems - BP430K (3.12 mb)
Home Theater Systems - BP430K (3.28 mb)
manual abstract
5. Use W/S to select the desired resolution then press ENTER (b) to confirm your selection. Connecting 14 Connecting 2 Connecting yIf your TV does not accept the resolution you have set on the player, you can set resolution to 576p as follows: 1. Press B to open the disc tray. 2. Press Z (STOP) for more than 5 seconds. yIf you select a resolution manually and then connect the HDMI jack to TV and your TV does not accept it, the resolution setting is set to [Auto]. yIf you select a resolution that your TV does not accept, the warning message will appear. After resolution change, if you cannot see the screen, please wait 20 seconds and the resolution will automatically revert back to the previous resolution. yThe 1080p video output frame rate may be automatically set to either 24 Hz or 50 Hz depending both on the capability and preference of the connected TV and based on the native video frame rate of the content on the BD-ROM disc. , Note Connecting to an Amplifier Make one of the following connections, depending on the capabilities of your existing equipment. • HDMI Audio connection (page 15) • Digital Audio connection (page 15) Since many factors affect the type of audio output, see “Audio Output Specifications” for details (page 56). About Digital Multi-channel sound A digital multi-channel connection provides the best sound quality. For this, you need a multichannel Audio/Video Receiver that supports one or more of the audio formats supported by your player. Check the logos on the front of the Audio/ Video receiver and the manual. (PCM Stereo, PCM Multi-Ch, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS and/or DTS-HD) Connecting 15 Connecting to an Amplifier via Connecting to an Amplifier via HDMI Output Digital Audio Output Connect the player’s HDMI OUT jack to the Connect the player’s COAXIAL OUT jack to the corresponding in jack on your amplifier using a corresponding in jack on your amplifier using an HDMI cable. optional digital audio cable. 2 Connecting Rear of the unit HDMI cable Coaxial cable Receiver/Amplifier Rear of the unit HDMI cable TV Receiver/Amplifier You will need to activate the player’s digital output. (See “[AUDIO] Menu” on page 23.) Connect the amplifier’s HDMI output jack to HDMI input jack on your TV using a HDMI cable if your amplifier has HDMI output jack. (Refer to amplifier’s owner’s manual) You will need to activate the player’s digital output. (See “[AUDIO] Menu” on page 23) 16 Connecting Connecting 2 Connecting to your Home Network This player can be connected to a local area network (LAN) via the LAN port on the rear panel. By connecting the unit to a broadband home network, you have access to services such as software updates, BD-Live interactivity and on-line content services. Wired network connection Using a wired network provides the best performance, because the attached devices connect directly to the network and are not subject to radio frequency interference. Please refer to the documentation for your network device for further instructions. Connect the player’s LAN port to the corresponding port on your Modem or Router using a commercially available LAN or Ethernet cable. yy When plugging or unplugging the LAN cable, hold the plug portion of the cable. When unplugging, do not pull on the LAN cable but unplug while pressing down on the lock. yy Do not connect a modular phone cable to the LAN port. yy Since there are various connection configurations, please follow the specifications of your telecommunication carrier or internet service provider. yy If you want to access content from DLNA servers, this player must be connected to the same local area network with them via a router. yy To set your PC as a DLNA server, install the supplied Nero MediaHome 4 on your PC. (see page 32) ,,Note Rear of the unit Router Broadband service DLNA certified servers Wired Network Setup If there is a DHCP server on the local area network (LAN) via wired connection, this player will automatically be allocated an IP address. After making the physical connection, a small number of home networks may require the player’s network setting to be adjusted. Adjust the [NETWORK] setting as follow. Preparation Before setting the wired network, you need to connect the broadband internet to your home network. If there is no DHCP server on the network and you want to set the IP address manually, select [Static] then set [IP Address], [Subnet Mask], [Gateway] and [DNS Server] using W/S/A/D and numerical buttons. If you make a mistake while entering a number, press CLEAR to clear the highlighted part. , Connecting 17 2 Connecting 1. Select [Connection Setting] option in the [Settings] menu then press ENTER (b). 2.Read the preparations for the network settings and then press ENTER (b) while [Start] is highlighted. Network will automatically be connected to the unit. Advanced Setting If you want to set the network settings manually, use W/S to select [Advanced Setting] on the [Network Setting] men...