Votes - 0, Average rating: 0
(
)
)
|
manual abstract
-The wireless RX and Wireless RX of blue LED indicator will flicker. 4. Release the ID/CHNNEL (ID./CH.) button of Wireless TX and ID button of Wireless RX. - ID is set up. Notes: If there is a product with a strong electromagnetic field nearby, interference may occur. Do not operate a portable transmitter (such as a wireless network device) near this product. CAUTION Rear speaker (wireless speakers) is no sound. The DC power cable is not connected the Wireless TX and main unit. Connect the Wireless TX and main unit with the DC power cable. Power cord of wireless RX (or wireless speakers) is not connected. Connect the Power cord of wireless RX (or wireless speakers). Sound is cut off. Change a channel of Wireless TX. (Follow steps “Changing a channel of Wireless TX and Wireless RX”) If rear speaker (wireless speakers) is no sound after operating as above, disconnect and connect the power cord of Wireless RX (or wireless speakers) or set up an ID of wireless TX and wireless RX (or wireless speakers). 11 Installation and Setup Changing a channel of Wireless TX and Wireless RX If there is a similar wireless product nearby, interference may occur. In this case, change to another channel using ID/CHANNEL (ID./CH.) button of Wireless TX. Manual setting Press ID/CHANNEL (ID./CH.) button for less than about 3 seconds. If the wireless TX and wireless RX signals do not match after operating as above, operate it again about three times. Auto setting 1Disconnect the DC power cable from the Wireless TX. 2Connect the DC power cable Wireless TX while you pressing the ID/CHANNEL (ID.CH.) button of Wiress TX. -The blue LED indicator will flicker. 3Disconnect the DC power cable from the Wireless TX and release the ID/CHANNEL (ID.CH.) button of Wiress TX. 4Connect the DC power cable Wireless TX. -The ID setting becomes optimization automaticly . Note: The wireless speakers may not receive the changed channel of transmitter (The LED of Wireless TX will turn blue. The The LED of Wireless RX will turn red). In this case set the ID as next paragraph. Setting an ID of Wireless TX and Wireless RX When the unit is manufactured, the ID is already set. If an interference occurs or you use a new Wireless RX, an ID is set again. 1. Set the wireless TX and wireless RX within 50cm of eachother. 2. Turn the Wireless TX and Wireless RX on. 3. Press the ID/CHNNEL (ID./CH.) button of Wireless TX and ID button of Wireless RX at the same time for more than about 3 seconds. -The wireless RX and Wireless RX of blue LED indicator will flicker. 4. Release the ID/CHNNEL (ID./CH.) button of Wireless TX and ID button of Wireless RX. - ID is set up. Notes: If there is a product with a strong electromagnetic field nearby, interference may occur. Do not operate a portable transmitter (such as a wireless network device) near this product. CAUTION Rear speaker (wireless speakers) is no sound. The DC power cable is not connected the Wireless TX and main unit. Connect the Wireless TX and main unit with the DC power cable. Power cord of wireless RX (or wireless speakers) is not connected. Connect the Power cord of wireless RX (or wireless speakers). Sound is cut off. Change a channel of Wireless TX. (Follow steps “Changing a channel of Wireless TX and Wireless RX”) If rear speaker (wireless speakers) is no sound after operating as above, disconnect and connect the power cord of Wireless RX (or wireless speakers) or set up an ID of wireless TX and wireless RX (or wireless speakers). HDMI Connection If you have a HDMI TV or monitor, you can connect it to this DVD/CD Receiver using a HDMI cable. 1. Connect the HDMI OUT jack on the DVD/CD Receiver to the HDMI jack on a HDMI compatible TV or monitor (H). 2. Set the TV’s source to HDMI (refer to TV’s Owner’s manual). 3. In stop mode, select HDMI mode by pressing HDMI. Press RESOL. repeatedly to select the resolution you wish to change. Notes: • The arrow on the cable connector body should face up for correct alignment with the connector on the DVD/CD Receiver. • If HDMI cable is not connected, the HDMI button is not operated. • If there is noise or lines on the screen, please check the HDMI cable. • Not all HDCP-compatible DVI devices will work with this DVD/CD Receiver. • If TV does not support HDCP, snow noise appears on the screen, or picture may be vibrated. Tip : When you use HDMI connection, you can change the resolution (576p, 720p, 1080i) for the HDMI output by pressing RESOL. on the remote control. About HDMI HDMI (High Definition Multimedia Interface) supports both video and audio on a single digital connection for an easy all- digital output to an HDMI or DVI-equipped TV. Connection to an HDMI TV requires an HDMI cable while connection to a DVI-equipped TV requires an HDMI to DVI adaptor. HDMI has the capability to support standard, enhanced, or high-definition video plus standard to multi-channel surround-sound audio, HDMI features include uncompressed digital video, a bandwidth of up to 5 gigabytes per ...