Votes - 0, Average rating: 0
(
)
)
|
manual abstract
2 Select [Setup], and then press OK. 3 Select [Preference] > [Disc Menu], and then press OK. 4 Select a menu language for discs, and then press OK. Note ••If your preferred disc language is not available, select [Others] from the list, and enter the 4-digit language code found at the the end of this user manual. ••If you select a language that is not available on a disc, the home theater uses the default language of the disc. Parental control Restrict access to discs that are recorded with ratings. Password You can set or change your password to play a restricted disc. 1 Press (Home). 2 Select [Setup], and then press OK. 3 Select [Preference] > [Change Password], and then press OK. »»A change password menu is displayed. 4 Follow the instructions on the TV to set or change password. • If you do not have a password or you have forgotten, enter 0000. 5 Press OK. Ratings Some discs are recorded with ratings according to age. You can set up your home theater to play only discs with an age rating lower than your child’s age. 1 Press (Home). 2 Select [Setup], and then press OK. 3 Select [Preference] > [Parental Control], and then press OK. »»A message prompts you to enter the password. 4 Enter the password with the Numeric buttons. 5 Select an age rating, and then press OK. • To play all discs irrespective of the rating, select level 8 or [Off]. Energy saving Save energy by changing the following settings. Auto standby When playing a disc or a USB storage device, automatically switch your home theater to standby if: • it is in pause or stop mode, and • no button is pressed for 30 minutes. 1 Press (Home). 2 Select [Setup], and then press OK. 3 Select [Preference] > [Auto Standby] > [On], and then press OK. Sleep timer Set timers to switch the home theater to standby after a specified time. 1 Press (Home). EN 2 Select [Setup], and then press OK. 3 Select [Preference] > [Sleep Timer], and then press OK. 4 Select the duration of the sleep timer. »»The sleep timer can be set up to 60 minutes. If the sleep timer is set to [Off], it switches off. 5 Press OK to activate. »»The home theater switches to standby after the specified time. Screen saver Automatically switch your home theater to screen saver mode if: • it is in pause or stop mode, and • no button is pressed for 10 minutes. 1 Press (Home). 2 Select [Setup], and then press OK. 3 Select [Preference] > [Screen Saver] > [On], and then press OK. Display panel Change the brightness of the home theater display panel. 1 Press (Home). 2 Select [Setup], and then press OK. 3 Select [Preference] > [Display Panel], and then press OK. 4 Select the brightness, and then press OK. Apply factory settings Reset your home theater to the default settings. You cannot reset the parental control settings. 1 Press (Home). 2 Select [Setup], and then press OK. 3 Select [Advanced] > [Restore default settings], and then press OK. 4 Select [OK], and then press OK. EN 7 Update software To continue to get the best features and support for your home theater, update the software regularly. Compare the version of your current software with the latest version on Check software version 1 Press (Home). 2 Select [Setup], and then press OK. 3 Select [Advanced] > [Version Info.], and then press OK. »»The software version is displayed. Update software through the Internet 1 Connect your home theater to the network through a wired connection (see 'Set up the wired network' on page 13). 2 Press (Home). 3 Select [Setup], and then press OK. 4 Select [Advanced] > [Software Update] > [Network]. »»If an upgrade media is detected, you are prompted to start or cancel the update. 5 Follow the instruction on the TV to confirm the update. »»When the software update is complete, the home theater automatically switches off and restarts. If it does not, disconnect the power cord for a few seconds and then reconnect it. Note ••If the home theater cannot connect to the Philips server, press (Home). ••Select [Setup] > [Network] > [Network Installation] to set up the network. Update software through USB What you need • A USB flash drive, with at least 75MB of memory. The USB flash drive must be FAT or NTFS formatted. Do not use a USB hard drive. • A computer with Internet access. • An archive utility that supports the ZIP file format (for example, WinZip® for Microsoft® Windows® or Stufflt® for Macintosh®). Step 1: Download the latest software 1 Connect a USB flash drive to your computer. 2 In your web browser, go to com/support. 3 At the Philips Support website, find your product and locate the Software and drivers. »»The software update is available as a zip file. 4 Save the zip file in the root directory of your USB flash drive. 5 Use the archive utility to extract the software update file in the root directory of the USB flash drive. »»The files are extracted under the UPG_ALL folder of your USB flash drive. 6 Disconnect the USB flash drive from your computer. EN Step 2: Update the...