Votes - 1, Average rating: 4
(
)
)
|
Photos and specs Yamaha YHT-292 |
manual abstract
Choices: OFF*, ON Dimension DIMENSION Function: Gradually adjusts the sound field either towards the front or towards the rear. Control range: –3 (towards the rear) to +3 (towards the front), initial setting is STD (standard). Center width CT WIDTH Function: Adjusts the center image from all three front speakers to varying degrees. A larger value adjusts the center image towards the front left and right speakers. Control range: 0 (center channel sound is output only from center speaker) to 7 (center channel sound is output only from front left and right speakers), initial setting is 3. For Music Enh. 2ch and Music Enh. 5ch Effect level Function: Adjusts the effect level. Choices: LOW, HIGH* ¦ Using sound field programs without surround speakers (Virtual CINEMA DSP) Virtual CINEMA DSP allows you to enjoy the CINEMA DSP sound field programs without surround speakers. When you set “SUR. L/R” to “NONE” (see page 33), Virtual CINEMA DSP is activated automatically whenever you select a CINEMA DSP sound field program (see page 25). ¦ Enjoying multi-channel sources and sound field programs with headphones (SILENT CINEMA) SILENT CINEMA allows you to enjoy multi-channel music or movie sound through ordinary headphones. SILENT CINEMA is activated automatically whenever you connect headphones to the PHONES jack while listening to CINEMA DSP sound field programs (see page 25). y • When it is activated, the SILENT CINEMA indicator lights up on the front panel display. ¦ Enjoying unprocessed input sources (Straight decoding mode) When this unit is in the “STRAIGHT” mode, 2-channel stereo sources are output from only the front left and right speakers. Multi-channel sources are decoded straight into the appropriate channels without any additional effect processing. Press MSTRAIGHT (or press tSTRAIGHT) to select “STRAIGHT.” “STRAIGHT” appears on the front panel display. To deactivate the “STRAIGHT” mode Press MSTRAIGHT (or tSTRAIGHT) again so that “STRAIGHT” disappears from the front panel display. 26 En FM/AM tuning FM/AM tuning Overview You can use two tuning modes to tune into a desired FM/ AM station: ¦ Frequency tuning mode You can search or specify the frequency of the desired FM/AM station automatically or manually (see “FM/AM tuning operations” on this page). ¦ Preset tuning mode You can preset the desired FM/AM station in advance, and then recall the station by specifying the preset group and number (see “Selecting preset stations” on page 28). Note • Orient the connected AM loop antenna, or adjust the position of the end of the indoor FM antenna for the best reception. FM/AM tuning operations 1 Press NINPUT l / h repeatedly so that “TUNER” is displayed on the front panel display. 2 Press GBAND to select the reception band (FM or AM). 3 To search the station automatically, press ITUNING AUTO/MAN’L so that the AUTO indicator lights up on the front panel display. To search the station manually, press ITUNING AUTO/MAN’L again so that the AUTO indicator disappears from the front panel display. Lights up during automatic tuning AUTO A AM 1440 kHz No colon (:) If a colon (:) appears on the front panel display, automatic/manual tuning is not possible. Press DEDIT PRESET/TUNING to turn the colon (:) off. 4 To begin automatic tuning, press FPRESET/TUNING l / h once. To tune into the desired station manually, press FPRESET/TUNING l / h repeatedly. When this unit is tuned into a station, the TUNED indicator lights up and the frequency of the received station is shown on the front panel display. • To tune into a higher frequency, press FPRESET/TUNING h. • To tune into a lower frequency, press FPRESET/ TUNING l. Note • If the signal from the station you want to select is weak, tune into it manually. Preset FM/AM stations Use this feature to store up to 40 stations (A1 to E8: 8 preset station numbers in each of 5 preset station groups). Preset the desired stations to this unit by using the automatic or manual station preset. Automatic station preset You can use the automatic preset tuning feature to store up to 40 FM stations with strong signals in order. 1 Press NINPUT l / h repeatedly so that “TUNER” is displayed on the front panel display. 2 Press GBAND to select “FM” as the reception band. 3 Press and hold HMEMORY for more than 3 seconds. The preset station number as well as the MEMORY and AUTO indicators flashes. After approximately 5 seconds, automatic presetting status from the current frequency and proceeds toward the higher frequencies. Flashes AUTO MEMORY A1:FM 87.50MHz Flashes When automatic preset tuning is completed, the front panel display shows the frequency of the last preset station. y • You can select the preset station group and the preset station number where the first received station will be stored by pressing EA/B/C/D/E and then FPRESET/TUNING l / h. Notes • Any stored station data existing under a preset station number is cleared when you store a new station under the same preset station number. • Only FM ...
Other models in this manual:Home Theater Systems - YHT-392 (2.04 mb)