Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
The delay time is that time difference between when the sound from the main channels can be heard and the surround sound can be heard. Setting a longer delay time makes the sound field feel larger, while setting a shorter delay time makes it feel smaller. 1Press MENU to display “Delay Time”. MENU 2Press + or – to adjust the delay time. – + y • Adjustable range – For Dolby Digital (except for 2 ch)/DTS input: 0 to 15 ms (factory setting: 5 ms) – For the other inputs: 15 to 30 ms (factory setting: 20 ms) If the delay time level of a signal input is adjusted, that of other signal inputs will be changed. For example, when the delay time of the Dolby Digital (except for 2 ch)/DTS input is adjusted from 0 ms (minimum) to 5 ms, that of the other signal inputs will be adjusted from 15 ms (minimum) to 20 ms automatically. When the setting is completed After about 10 seconds, the unit returns to the main display (“input name” or “DSP program name” display). Or, press MENU until the main display appears. REMOTE CONTROL OPERATING OTHER COMPONENTS USING THE REMOTE CONTROL REMOTE CONTROL OPERATING OTHER COMPONENTS USING THE REMOTE CONTROL Setting the manufacturer code (remote control signal assigned to each manufacturer) for your TV, VCR or DVD player on the remote control allows you to operate not only the AV-S77 but also your TV, VCR or DVD player using the remote control. Notes • Remote control of certain components may not be possible depending on the model and the year of make even though its manufacturer is listed on the back cover. • Depending on the model, certain components from other manufacturers cannot be controlled, or only limited functions can be controlled, even though the proper manufacturer code has been set. If you encounter this problem, please use the remote control supplied with the component. • Setting the manufacture code can not be performed if the component to be controlled does not support remote control operation. y • The manufacturer code 11 has been set for the remote control selector buttons (TV, VCR and DVD) at the factory. Setting the Manufacturer Code 2Keeping CODE SET pressed, enter the 2-digit manufacturer code for the component to be controlled using the numeric buttons. 1234 CODE SET + s a d w 5678 y • You can release CODE SET after entering the code. • Refer to the list of manufacturer codes on the back cover. 3 3Press POWER and check that the component to be controlled turns on and off (standby). POWER 2 1 POWER —— MEMORY —— AV-S77 1 2 3 MENU LEVEL TEST DISPLAY – + EFFECT ON/OFF MUTE NIGHT h h + g g h q w g – B. BOOST POWER INPUT TV VOL + CH – CH + TV VOL – DSP VOL 1 2 TV MUTE ENTER 3 4 5 6 7 8 s a d w t y e r CODE SET DVD VCR TV TV INPUT TITLE MENU 1While pressing CODE SET, press the remote control selector button (TV, VCR or DVD) for which the manufacturer code is to be set. CODE SET DVD VCR TV + PREPARATION OPERATION REMOTE CONTROL APPENDIX A manufacturer code of TV, VCR or DVD can be set for the TV, VCR or DVD button respectively. E-31 English OPERATING OTHER COMPONENTS USING THE REMOTE CONTROL ¦ Precautions when performing the setting You can operate the component using the TV, VCR or DVD operation buttons on the remote control once the manufacturer code is set properly. If unsuccessful, perform the procedure from step 1 again. Pay attention to the following points when you perform the procedure. • Check that the correct remote control selector button has been selected when setting the manufacturer code. • If more than one code is given for a manufacturer, try entering each code in the order given. • Remove and replace the remote control’s batteries (complete this step within 2 minutes) and then perform the procedure. While replacing the batteries, be sure not to press any button on the remote control. Doing so may erase the manufacturer code which has been set for other remote control selector buttons. ¦ To reset the manufacturer code to the factory-set code Follow steps 1 to 2 for the procedure “Setting the Manufacturer code”, and enter “11” while pressing CODE SET in step 2. (It is not necessary to follow step 3.) OPERATING OTHER COMPONENTS USING THE REMOTE CONTROL Controlling a TV OPERATING OTHER COMPONENTS USING THE REMOTE CONTROL Controlling a TV You can control your TV by setting the corresponding manufacturer code for the remote control selector button “TV”. TV 1 Press TV. PREPARATION OPERATION REMOTE CONTROL APPENDIX POWER —— MEMORY —— AV-S77 1 2 3 MENU LEVEL TEST DISPLAY – + EFFECT ON/OFF MUTE NIGHT h h + g g h w g – B. BOOST POWER INPUT TV VOL + CH – CH + TV VOL – DSP VOL 1 2 TV MUTE ENTER 3 4 5 6 7 8 s a d w t y e r CODE SET DVD VCR TV TV INPUT TITLE MENU TV power ON/OFF (standby) Selects the next lower channel Stops the VCR* Records on the VCR* Increases TV volume Selects TV input Selects the next higher channel Mutes the TV Decreases TV volume Plays the VCR* Pauses the VCR* Fast forwards the VCR* Rewinds the VCR* 1 y • A VCR can be controlled using * marked butto...