Login:
Votes - 5, Average rating: 4.4 ( )

User manual Sony, model DAV-S300

Manafacture: Sony
File size: 942.84 kb
File name: 4226344321.pdf
Language of manual:ensl
Free link for this manual available at the bottom of the page



manual abstract


Height diagram Getting 60 30 DCDC • R. HGT. LOW Select this if the rear speakers are located in the section D. • R. HGT. HIGH Select this if the rear speakers are located in the section C. These parameters are not available when “REAR“ is set to “NO”. 15 Getting Started Speaker Setup To specify the balance and level of the speakers 1 Press TEST TONE on the remote. You will hear the test tone from each speaker in sequence. 2 Press AMP MENU repeatedly to display <> on the front panel display. 3 Sit at your listening position and select the item to be adjusted using M/m. • Items adjusted in << LEVEL >> -Balance of the front and rear speakers -Volume level of the center and rear speakers and subwoofer 4 Adjust the volume level so that the volume of the test tone from each speaker sounds the same using >. If you do not operate the remote for a few seconds, the value turns off and is stored in the system. 6 Press TEST TONE again to turn off the test tone. x Balance You can vary the balance of each speaker as follows. The default adjustments are in the parentheses. •F ___I___ (center) (front speakers) Adjust the balance between the front left and right speakers (6 dB (L) to 6 dB (R), 1 dB steps). •R ___I___ (center) (rear speakers) Adjust the balance between the rear left and right speakers (6 dB (L) to 6 dB (R), 1 dB steps). x Level You can vary the level of each speaker as follows. The default adjustments are in the parentheses. • C. LEVEL (0 dB) (center speaker level) Adjust the level of the center speaker (–6 dB to +6 dB, 1 dB steps). • R. LEVEL (0 dB) (rear speakers level) Adjust the level of the rear speakers (–6 dB to +6 dB, 1 dB steps). • S. W. LEVEL (0 dB) (subwoofer level) Adjust the level of the subwoofer (–6 dB to +6 dB, 1 dB steps). z You can adjust the level of center/rear speakers and subwoofer directly Use the CENTER/REAR/WOOFER +/– buttons on the remote. Notes • When you select an item, the sound cuts off for a moment. • Depending on the settings of other speakers, the subwoofer may output excessive sound. To adjust the volume of all the speakers at one time Use the VOLUME control. Using the optional speaker stands For greater flexibility in the positioning of the speakers, use the optional WS-FV10 floor stand (available only in certain countries). WS-FV10 floor stand 16 Presetting Radio Stations You can preset 20 stations for FM and 10 stations of AM. Before tuning, make sure that you have turned down the volume to the minimum. BAND PRESET +/– TUNING +/– ENTER 1 2 3 4 5 6 7 8 9 >10 10/0 MEMORY 1 Press BAND repeatedly until the band you want appears on the front panel display. Every time you press BAND, FM and AM changes alternately. 2 Press and hold TUNING + or – until the frequency indication starts to change, then release. Scanning stops when the system tunes in a station. “TUNED” and “STEREO” (for stereo program) appear on the front panel display. 3 Press MEMORY. A preset number appears on the front panel display. 4 Press PRESET + or – to select the preset number you want. 5 Press ENTER. The station is stored. 6 Repeat Steps 1 to 5 to store other stations. To tune in a station with a weak signal Press TUNING + or – repeatedly in Step 2 to tune in the station manually. To change the preset number Start over from Step 1. To change the AM tuning interval The AM tuning interval is factory set to 9 kHz. To change the AM tuning interval, tune in any AM station first, then turn off the power. While holding down the ENTER button, turn the power back on. When you change the interval, AM preset stations will be erased. To reset the interval, repeat the same procedure. Getting 17 Playing Discs Playing Discs Depending on the DVD or VIDEO CD, someThis chapter describes how to play a operations may be different or restricted. Refer to the DVD/CD/VIDEO CD. instructions supplied with your disc. Connect headphones. Adjust the volume. ?/1 (POWER) AH 1 Turn on the TV and select the video input so that you can view the pictures from this system. 2 Press ?/1 (POWER) to turn on the system. The ?/1 (POWER) button changes to green and the front panel display lights up. 3 Press A, and place the disc on the disc tray. With the playback side facing down 4 Press H. The disc tray closes, and the system starts playback (continuous play). Adjust the volume by rotating VOLUME. After following Step 4 xWhen playing a DVD A DVD menu or title menu may appear on the TV screen (see page 24). xWhen playing a VIDEO CD The menu screen may appear on the TV screen depending on the VIDEO CD. You can play the disc interactively, following the instructions on the menu screen. (PBC Playback, see page 25.) zYou can turn on the system using the remote Press ?/1(POWER) when the indicator by the ?/1(POWER) button on the front panel is lit in red. Notes • If you leave the system in pause or stop mode for 15 mi...


Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category