Votes - 3, Average rating: 5 ( )

Manafacture: Haier File size: 429.25 kb File name: Language of manual:

Hole Cover 13. Upper Hinge Axes Bushing 14. Door Bushing 15. Axis Bushing Screw 16. Lower Hinge Axes Bushing 17. Handle 18. Spring Gasket 19. Flat Gasket 20. Handle Screw 1. Remove the screw cover from the upper hinge cover. Use a Phillips head screwdriver to remove the screw that holds the upper hinge cover in place. Remove the upper hinge cover. Loosen and remove the screws that hold the upper hinge in place. Note: Make sure you hold door to prevent it from falling or being damaged. Lift and set aside for now. Remove both of the upper hinge hole covers (left side) and set aside. English 67 345 1 2 2 1 English 13 13 16 15 14 12 16 12 14 15 2. Remove the hole cover from the upper left side of door. Remove the upper hinge block from right side of door. Replace upper hinge block on the left side of door. Replace the hole cover to the hole on the right. 3. Remove lower right hinge cover Loosen and remove the screws that hold the lower right hinge in place Remove the doorstopper on the bottom left and replace them on the bottom right (where hinge was just removed). Unscrew and move pin from right side position on hinge to left side position on hinge. (Requires 9/32" hex socket.) Place lower hinge removed from lower right to lower left side and fasten in place with the screws. Replace lower hinge cover. 4. Lay door down on a sturdy surface Remove door seal (gasket) from rear side on door Note: Do not use sharp instrument (knife, etc.). Remove hole covers on right front side of door. Use Phillips screwdriver to remove the two (2) screws that hold the door handle in place on left side. Note: Do not lose washer. Place 1st screw through top hole on right side and screw into handle. (Do not tighten completely at this time.) Place 2nd screw through bottom hole and screw into handle and tighten. Now tighten the 1st (upper) screw completely. Replace hole cover previously removed into the open holes on left front side of door. 5. Take door in hand and place bottom left hole in door over bottom left hinge pin and put into place. Note: Make sure you hold door to prevent it from falling or being damaged. Take previously removed upper hinge and place it in upper left hole of door. Take screws and tighten upper hinge to cabinet of unit. Note: Make sure door is level and closes properly (no gaps). If it does not, loosen upper hinge screws slightly and adjust door and retighten. Do this until door is level and closes properly. 10 Replace hinge cover and tighten with screw. Replace screw cover. English Replacing Light Bulb 1. Turn off the wine cellar and unplug the power cord. 2. To remove the light bulb cover use a Phillips head screw driver to remove the 3 screws. 3. Make sure the light bulb is cool before removing it. Replace using a light bulb 10 watts or less. 4. After the bulb is secure, install the light bulb cover and replace the three screws. 5. Turn unit on to its original setting after plugging in the power cord. 11 English PROPER WINE CELLAR CARE & CLEANING Cleaning and Maintenance Warning: • To avoid electric shock always unplug your wine cellar before cleaning. Ignoring this warning may result in death or injury. Caution: • Before using cleaning products, always read and follow manufacturer’s instructions and warnings to avoid personal injury or product damage. General: • Prepare a cleaning solution of 3-4 tablespoons of baking soda mixed with warm water. Use sponge or soft cloth, dampened with the cleaning solution, to wipe down your wine cellar. • Rinse with clean warm water and dry with a soft cloth. • Do not use harsh chemicals, abrasives, ammonia, chlorine bleach, concentrated detergents, solvents or metal scouring pads. SOME of these chemicals may dissolve, damage and/or discolor your wine cellar. Door Gaskets: • Clean door gaskets every three months according to general instructions. Gaskets must be kept clean and pliable to ensure a proper seal. • Petroleum jelly applied lightly on the hinge side of gaskets will keep the gasket pliable and ensure a good seal. Power Interruptions • Occasionally there may be power interruptions due to thunderstorms or other causes. Remove the power cord from wall outlet when a power outage occurs. When power has been restored, replug power cord to wall outlet. Vacation and Moving Care • For long vacations or absences, unplug the wine cellar and clean the wine cellar and door gaskets according to “General cleaning” section. Prop doors open, so air can circulate inside. When moving always move the wine cellar vertically. Do not move with the unit lying down. Possible damage to the sealed system could occur. 12 English TROUBLESHOOTING Wine Cellar does not operate • Check if wine cellarr is plugged in. • Check if there is power at the AC outlet by checking the circuit breaker. Wine appears too warm • Frequent door openings. • Allow time for recently added wine to reach desired temperature. • Check gaskets for proper seal. • Adjust temperature control to colder setting. Wine tempe...

Download now

Please, enter two numbers from picture: