Votes - 5, Average rating: 4 ( )

Manafacture: Sub-Zero File size: 5.66 mb File name: Language of manual:

The overlay Model ICB424/O is designed to accept a decorative door panel to match surrounding cabinetry. The door panel and the handle will be provided by the customer. The solid door Model ICB424S—with no glass window—requires a different door panel than the glass door design. Before beginning installation, check for the correct components for the fit and finish desired. All overlay doors require a decorative panel 603 mm by 764 mm and a minimum 16 mm thick. If you have questions, contact your Sub-Zero dealer or cabinet supplier. Additional panel information can be found in the Sub-Zero Design Guide. MODELS ICB424 ICB424FS PANEL DESIGN Additional panel design information can be found in the Sub-Zero Design Guide. Check our website at subzero.com. Kickplate Illus. 8 MODELS ICB424 AND ICB424FS INSTALLATION MODELS ICB424 ICB424FS PANEL DESIGN Additional panel design information can be found in the Sub-Zero Design Guide. Check our website at subzero.com. OVERLAY DOOR PANELS OVERLAY GLASS DOOR – MODEL ICB424 Inspect the door panel for the minimum 16 mm thickness, the finished inside edge and the 5 kg weight limit. See the Wine Storage section of the Sub-Zero Design Guide for additional panel information. Decide if the handle will be attached through the glass door frame or just through the decorative door panel. If it is just through the door panel, the handle must be attached first. Decorative panels are attached to the Model ICB424 door using #8 x 16 mm square drive screws passing through the door frame from the rear, behind the gasket into the panel. The door panel is marked for screw locations by the use of ‘tenon centers’, which are temporarily inserted into the 6 mm diameter holes in the front of the glass door frame. Refer to illustration 9 on page 11. With the Wine Storage unit secured in position and the door closed, the panel is held in the desired position on the door and rapped by hand from the front, putting center marks on the rear surface of the panel. If the door panel is made of such a material that pre-drilling is needed, all of the mounting holes should be marked. If not, only enough holes to hold the panel in place temporarily, are necessary. The door panel is then lowered from the door frame, tenon centers removed, the door opened and the screws driven into the panel through the black tape on the door frame, using the center marks to locate the screws. The screw holes inside the door are hidden under a cover flap on the door gasket. It is necessary to lift the flap to insert the screws. Use as many screws as necessary to hold the door panel in place properly. IMPORTANT NOTE: After the first three or four mounting screws are in place, but not completely tightened, close the door and check your panel fit. This is the time to make small adjustments. Once you are satisfied with the appearance, open the door and apply the remainder of the screws. Check all screws for tightness. The metal frame on the glass door has numerous mounting holes on each side of the door. This is to accommodate the Sub-Zero accessory handles and provide for easy attachment of the handle through the door frame. If you choose not to use the pre-drilled handle mounting holes, it will be necessary to fasten the handle from the rear of the door panel only, or drill one or more additional holes through the metal frame of the glass door. Illustration 10 on page 11 shows how this hole passes through the door frame. The hole center is on the small locator groove in the front of the frame. A 6 mm diameter hole is made in the front wall of the extrusion and an 11 mm diameter hole through the rest of the frame. The wine storage unit door is made with a sealed double wall tempered glass core. The drill must not contact this core when drilling. Be sure the hole is centered on the small groove in the front of the door frame and the drill passes squarely through the frame. If you are inexperienced with drilling, fasten the handle from the rear of the door panel only. MODELS ICB424 AND ICB424FS INSTALLATION IMPORTANT NOTE: Install screws in all the mounting holes in the door frame. The nature of the door panel with a narrow outer rim and no connecting center member requires the support provided by the glass door. After the door panel installation is complete, apply the cover patches or plugs provided over the holes on the inside surface of the door. The cover patches or plugs are part of the insulation system on the door of the Wine Storage unit. Be sure to cover all the holes in the door that were used. OVERLAY SOLID DOOR – MODEL ICB424 IMPORTANT NOTE: The solid door panel for the Model ICB424 must be a minimum of 16 mm thick and cannot exceed 9 kg. Installation of the solid door panel is the same as the door panel for a glass door model. A solid panel must not be installed on a glass door unit, as this may cause moisture to form behind the panel. HINGE ADJUSTMENT MODELS ICB424 IMPORTANT NOTE: The Wine Storage unit ICB424FS must be ins...

Download now

Please, enter two numbers from picture: