Votes - 4, Average rating: 4.5 ( )

Manafacture: PUR Water Purification Products File size: 1.62 mb File name: Language of manual:

Do not put the drip tray in the dish washer. To replace the drip tray, push the tray down into the drip tray area until securely in place. NIGHT LIGHT • Your unit is equipped with a special night light feature for nighttime safety. To turn the nightlight on or off while continuing to provide power to the cooler, use the green switch on the back of the unit. HEATING AND COOLING LIGHTS • Heating and Cooling Lights indicate when the water is not ready to dispense. A red light will shut off when hot water is ready and a blue light will shut off when the cold water is ready to dispense. COLD KNOB • You can regulate the cold temperature of your water by adjusting the knob on the back of the unit. Turn the knob to any setting between min. and max. to suit your temperature preference. Proper Care and Cleaning WARNING! • Always unplug the unit before cleaning to avoid electric shock. SECTION I-PERIODIC CLEANING • Hand-wash all components: Reservoir, filter tray, fill tank, fill tank cap, drip tray basin, drip tray grille and float valve with mild soapy water. Rinse each component with water. SECTION II-ANNUAL CLEANING 1. Turn off all-3 switches on the back of the unit and unplug electrical cord from wall. 2. Remove and drain fill tank. 3. Remove water from unit by placing a 3-gallon bucket under the drain plug. Unscrew drain plug to release water into the bucket. Caution-water could be hot. Replace drain plug. 4. Dispense remaining water by pressing cold temperature button (marked with blue waves), room temperature button (gray waves) and hot temperature water (marked with red waves) into a large glass. 5. Remove the filters from the unit and throw them away to ensure unit is completely clean. 6. Vacuum or brush the condenser coils on the rear of the unit if dust is present. (See figure 13) 7. Prepare a solution of 4 tsp (20ml) of common household bleach (5.25% sodium hypochlorite) to 1 gal (4 liters) of room temperature water. 8. Pour the bleach solution into the fill tank. Put the fill tank back onto the unit. Let bleach solution flow through the unit and wait for 5 minutes. 9. Drain all the bleach solution from the cooler by repeating steps 3 and 4. 13 10. Rinse the cooler by filling the reservoir with clean water and draining by repeating steps 3 and 4 to remove water. Repeat rinsing step one more time to ensure the system is thoroughly rinsed. Wipe away any residue on each part including the chilling area with a clean damp cloth. 11. Install new filters and refill the unit with water. (See Pre-activating & Installing the Filter System for more details.) 12. Plug-in unit and turn on all power switches. Storing Unit 1. Follow steps 1-6 under the Proper Care and Cleaning Section II-Annual Cleaning. 2. When moving, the unit must be stored vertically. DO NOT store the unit on its side as this may cause possible damage to compressor. 3. When removing the unit from storage, you may want to follow the direction suggested under Proper Care and Cleaning. Frequently Asked Questions How long will it take for the water to filter through? • The system will take less than 1 hour for the water to filter through and chill or heat the water to be ready for dispensing. Does the filter dry up if I don’t use it? • Yes, the filters can dry up if left dry for any period of time. • Repeat Pre-activating and Installing the Filter System directions, steps 1, 4 & 5. Where will we be able to find PU. R Ultimate (CRF-950) Replacement Filters for the PU. R Water Filtration System? • The filters may be purchased at most retail outlets. I found an extra white part the shape of a circle with a pole sticking out the center on one side. What do I do with it? • This is called a baffle - it helps separate the room temperature water from the cold water in the chilling area. The chilling area is underneath the reservoir. Remove the fill tank, filter tray and reservoir to access the chilling area. Refer to the illustration on page 2. With the pole end in, insert the baffle inside the unit and resecure the pole into the hole provided. Troubleshooting Unfiltered water leaks into the filtered water reservoir. • Check that the filter that has been twisted firmly into place. (See Pre-activating & Installing the Filter System, step 7) The Filter Life Indicator doesn’t seem to be moving. • Remove the filter cartridge from the fill tray and rinse under tap water for a few seconds and replace. Cannot remove the filter tray. • To remove the filter tray, grasp the top of the filters firmly and lift up to remove. The unit does not operate. • Check if the unit is plugged in and the power switch is in the ON position. • Check your house circuit breaker to make sure there is power at the outlet. Hot water isn’t hot • Check if the hot water switch is in the ON position. • Too much hot water may have been used in too short a period of time. Wait for the indicator light to turn off before dispensing. The cold water isn’t cold. • Check if the power switch is in the ON ...

Download now

Please, enter two numbers from picture: