When the wine cooler is not to be used for a long period of time, disconnect the plug and leave the door partially open. NOTE: Wait 3 to 5 minutes before restarting if operation has been interrupted. Interior Light The operation of the interior light is "manually" controlled and does not operate with the opening or closing of the door. To operate the light; manually press the “light” key pad located on the electronic control panel NOTE: Leaving the interior light on for extended time periods, will increase the internal temperature of the cabinet Defrosting Your wine cooler is designed with an “Auto-Cycle” defrost system. What is Auto Cycle defrost? The refrigerated surfaces of the fresh food compartment defrost automatically, during the “off” cycle of the cold control. (thermostat) Defrost water from the fresh food compartment is disposed of automatically, by means of being channeled onto a drip tray located on the compressor. Heat transfer from the compressor causes the defrost water to evaporate. ELECTRONIC CONTROL OPERATION; The electronic LED display on this wine cooler is programmed to display (independently) the following temperature (only) information. "INTERNAL CABINET TEMPERATURE: This setting is represented by a "steady" state (non-flashing) LED display and is the normal (LED) default setting during operation. SET OPERATING TEMPERATURE: This setting is represented by a "flashing" LED display and can only be programmed (SET) by pressing and releasing either of the +/-(temperature) keys during operation. NOTE: The set temperature can only be adjusted/set while the LED is in "flashing" mode. 2 CARE & MAINTENANCE DEFAULT SETTINGS: When the unit is first connected to a 120V/60Hz power supply, (and/or in the event of a power failure) temperature settings automatically revert to the following default settings; The LED default setting for the internal (cabinet) temperature is the "real time" (ambient) temperature measured at the time the unit is connected or power is restored. The LED default setting for the set operating temperature is 50.F / 10.C. (after a power failure has occurred, the previously set temperature is automatically erased and will have to be re-set) The LED default setting for temperature selection (.F/.C) is .F. (Farenheight Scale) SETTING OPERATING TEMPERATURE: To set/change the operating temperature; 1. Press and release either of the +/- (temperature) keys. The LED display will temporarily reveal the (flashing) set temperature for approximately 5 seconds. (If you fail to set/change the operating temperature within this 5 second period, the LED will automatically revert back and display the internal (cabinet) temperature. 2. Each depression of the +/- key (during flashing mode) will increase the temperature incrementally by 1. (Temperature ranges between 43.F ~ 57.F / 6.C ~ 14.C) 3. Each depression of the +/- key (during flashing mode) will decrease the temperature incrementally by 1. (Temperature ranges between 43.F ~ 57.F / 6.C ~ 14.C) The operating temperature will "flash" in the LED display for approximately 5 seconds after the selection is made, then revert back to display the internal (cabinet) temperature. TEMPERATURE SELECTION (.F/.C): This unit can display temperatures on the "Farenheight" or "Celsius" scale. Press the temperature selector keypad to alternate between .F/.C scale. The "blue" indicator light adjacent to the corresponding mode will illuminate to signify the selection made. Cleaning To clean the inside, use a soft cloth and a solution of a tablespoon of baking soda to one quart of water, or a mild soap suds solution, or some mild detergent. Clean the wooden wine racks (shelves) using a lightly dampened cloth then dry throughly with a soft cloth. Clean the outside with a soft damp cloth and some mild detergent or appliance cleaner. Vacation Time For short vacation periods, leave the electronic controls at their usual settings. During longer absences, (a) remove bottles, (b) disconnect from electrical outlet, (c) clean the wine cooler thoroughly, (d) leave door open to avoid possible formations of condensate, mold or odors. Power Failure Most power failures are corrected within an hour or two and will not affect the internal temperature of your wine cooler. Try and minimize the number of door openings while the power is off. During power failures of longer duration, take steps to protect your wine.When power is restored, the previously “set” operating temperature is automatically erased and must be re-programmed. (See Setting Operating Temperature) If You Move Remove or securely fasten down all loose items inside the wine cooler. To avoid damaging the leveling screws, turn them all the way into the base. Light Bulb Replacement To replace the interior light bulb; Remove the screw holding the light bulb cover, remove cover. Unscrew light bulb. Replace light bulb. NOTE: This aplliance uses a standard 40 watt appliance bulb only. (available at most local hardware store...