Login:
Votes - 3, Average rating: 4 ( )

User manual GE Monogram, model Wine Chiller Wine Reserve and Beverage Center

Manafacture: GE Monogram
File size: 169.41 kb
File name:
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


IMPORTANT – Observe all governing codes and ordinances. Note to Installer – Be sure to leave these instructions with the Consumer. Note to Consumer – Keep these instructions with your Owner’s Manual for future reference. WARNING – This appliance must be properly grounded. See “Electrical Supply”, page 4. AVERTISSEMENT – Cet appareil doit etre correctement mis a la terre. Consulter <>, page 4. If you received a damaged wine chiller, wine reserve or beverage center, you should immediately contact your dealer or builder. Skill Level – Installation requires basic mechanical skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. • Use this appliance only for its intended purpose. • Immediately repair or replace electrical service cords that become frayed or damaged. • Unplug the unit before cleaning or making repairs. • Repairs should be made by a qualified service technician. AVERTISSEMENT : • Il ne faut utiliser cet appareil que pour l’usage pour lequel il a ete construit. • Il faut reparer ou remplacer immediatement tout cordon d’alimentation electrique effiloche ou endommage. • Debrancher le bar ou le refrigerateur a vin avant le nettoyage ou toute intervention. • Les reparations doivent etre faites par un technicien qualifie. For Monogram local service in your area, call 1.800.444.1845 For Monogram service in Canada, call 1.888.880.3030 For Monogram Parts and Accessories, call 1.800.626.2002. monogram.com CONTENTS Design Guide The Installation Space ............................ 3 Product Clearances ................................ 3 Side-by-Side Installation ........................ 3 Installation Instructions Tools, Hardware ....................................... 4 Grounding the Product ........................... 4 Staining Wood Drawer Fronts ............... 4 Step 1, Remove Packaging .................... 4 Step 2, Reverse Door Swing .................. 5 Step 3, Leveling ........................................ 6 Step 4, Connect Power ........................... 6 Step 5, Slide Product into Cutout .......... 6 Step 6, Install Nameplate ....................... 6 Step 7, Set Temperature Controls ......... 6 Template for Nameplate ...... Back Cover 2 Design Guide THE INSTALLATION SPACE The cutout depth should be 24. The cutout dimensions shown allow for a full door swing and access to the pull-out racks when installed as a built-in in standard 24. deep cabinets. • The wine chiller, wine reserve and beverage center can be installed freestanding. • If installing between frameless cabinets, a 1/2. wide filler strip or side panel may be needed on hinge side. The filler strip will act as a spacer between the case and adjacent cabinet door swing. The width of the opening must include the filler panels. NOTE: The door should protrude 1. beyond the surrounding cabinets. Additional Specifications • A 120 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall as shown. Electrical must be located on rear wall as shown. NOTE: GFI (ground fault interrupter) is not recommended. PRODUCT CLEARANCES The wine chiller, wine reserve and beverage center is factory set for a 110° door swing. When installed in a corner: • Allow 4. min. clearance on the hinge side for the 90° door swing and to allow racks to slide out. • Allow 10. minimum clearance on the hinge side for a full 110° door swing. • The door swing is reversible on all models. If desired, change the door swing before installation. Choose the location: • These products may be closed in on the top and three sides as long as the front is unobstructed for air circulation and proper access to the door. • Do not install these products where the temperature will go below 55°F (13°C) or above 90°F (32°C). • Do not install where it will be subject to direct sunlight, heat or moisture. • These products are not designed to be stacked one over the other. Black or Stainless Steel Toekick Options • These products are shipped with a black toekick installed. An optional stainless steel toekick is also supplied with each product. For shipping purposes, the stainless steel toekick is secured to the back of the unit. 90° Door Swing SIDE-BY-SIDE INSTALLATIONS Increase storage capacity by installing two Monogram beverage centers, wine chillers or wine reserves together. Or, for a complete refreshment center, install any two of these units together. • A side-by-side installation requires at least a 47-1/2. wide opening. No trim kits required. • Products must operate from separate, properly grounded receptacles. 10" Minimum to Wall 110° 21-5/8" 23-5/8" 4" Minimum to Wall 90° 34-1/2"-35" 24" 47-1/2" Min. 1-1/2" 9" 10-1/2" 9" 10-1/2" 14" 15" Locate Outlet 23-3/4" 34-1/2" 23-3/4" Locate Outlet 34-1/2...

Other models in this manual:
Water Dispensers - Wine Reserve and Beverage Center (169.41 kb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category