Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
CABINET CABINET Front edge of product case 110° Front face 120° These products will fit flush to adjacent cabinets when installed with a Dim. A-width filler panel or cleat. The filler panel should be recessed or set back behind the door and even with the front edge of the product case. NOTE: Handle and handle standoff depth is 1-3/4" Product Dim. A ZDWI240, ZDBI240 1" ZDWC240, ZDWR240 1/2" ZDBC240, ZDBR240 1/2" *For a standard installation of Custom-Framed unit: The product must be installed so that the front face will project 2" forward of adjacent cabinets. This position will allow a full door swing and prevent interference with adjacent cabinetry. The opening between cabinets must be 23-3/4" minimum. *For a standard installation of Stainless Steel unit: The product must be installed so that the front face will project 1-3/4" forward of adjacent cabinets. This position will allow a full door swing and prevent interference with adjacent cabinetry. The opening between cabinets must be 23-3/4" minimum. **For a flush installation of Stainless Steel unit: Install a 1/2"-wide filler strip on the hinge side. The filler strip will act as a spacer between the door case and adjacent cabinets and will prevent interference with the cabinet door swing. Recess the filler strip 2" back from the front face of the unit, or even with the front edge of the product case (behind the gasket). The width of the opening must be 24-1/4" (including the 1/2" filler strip). *** For a flush installation of Custom-Framed unit: Install a 1"-wide filler strip on the hinge side. The filler strip will act as a spacer between the door case and adjacent cabinets and will prevent interference with the cabinet door swing. Recess the filler strip 2" back from the front face of the unit, or even with the front edge of the product case (behind the gasket). The width of the opening must be 24-3/4" (including the 1" filler strip). • The wine chiller, wine reserve and beverage center can be installed freestanding. Additional Specifications • A 120 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall as shown. Electrical must be located on rear wall as shown. NOTE: GFI (ground fault interrupter) is not recommended. Standard Installation CABINET CABINET Front edge of product case Dim. A 110° Front face 120° In a standard installation, the product will project forward of adjacent cabinets. See Dim. A. Product Dim. A ZDWI240, ZDBI240 2" ZDWC240, ZDWR240 1-3/4" ZDBC240, ZDBR240 1-3/4" 3 Design Guide PRODUCT CLEARANCES The stainless steel wine chiller, wine reserve and beverage center is factory set for a 110° door swing. Models that accept custom panels have a 95° door swing. When installed in a corner: • Allow 4" min. clearance on the hinge side for the 90° door swing and to allow racks to slide out. • Allow 10" minimum clearance on the hinge side for a full 110° door swing. (Models ZDWI240WII and ZDBI240WII have a 95° door swing.) NOTE: Custom handle clearances may vary, depending on custom handle depth. SIDE-BY-SIDE INSTALLATIONS Increase storage capacity by installing two Monogram beverage centers, wine chillers or wine reserves together. Or, for a complete refreshment center, install any two of these units together. • A side-by-side installation requires at least a 47-1/2"- wide minimum opening for standard installation and a 48-1/2"-wide minimum opening for flush installation of stainless steel models. A 49-1/2"-wide minimum opening is required for side-by-side flush installation of custom framed models. • Products must operate from separate, properly grounded receptacles. 502Dia2110" Minimumto Wall110°* *95° Door Swing on Custom Frame Models 90° Door Swing 21-5/8" 23-5/8" 615Dia84" Minimumto Wall90. • The door swing is reversible on all models. If desired, change the door swing before installation or before installing the custom frame panel. Choose the location: • These products may be closed in on the top and three sides as long as the front is unobstructed for air circulation and proper access to the door. • Do not install these products where the temperature will go below 55°F (13°C) or above 90°F (32°C). • Do not install where it will be subject to direct sunlight, heat or moisture. • These products are not designed to be stacked one over the other. Black or Stainless Steel Toekick Options • These products are shipped with a black toekick installed. An optional stainless steel toekick is also supplied with each product. For shipping purposes, the stainless steel toekick is secured to the back of the unit. 4 Installation Instructions TOOLS REQUIRED • #2 Phillips screwdriver • Adjustable wrench PARTS SUPPLIED • Monogram nameplate • Hardware for changing door swing • Optional stainless steel toekick with screws and spacers • Left and right side hinge covers • Top screw hole cover Sta...