Votes - 3, Average rating: 4.3 ( )

Manafacture: Cornelius File size: 386.35 kb File name: ddd0d3de-205b-452b-aa38-3bf095448474.pdf Language of manual:

d. Place CO2 cylinder at right rear corner inside beer dispenser cabinet in upright position. Fasten CO2 cylinder with CO2 cylinder retainer (spring) provided. Hook both ends of retainer to holes in cold plate. (See Fig. 2.) WARNING: To avoid personal injury and/or property damage, always secure CO2 cylinder with retainer to prevent it from falling. Should CO2 cylinder valve become accidentally damaged or broken off, CO2 cylinder can become an unguided missile. 2. Installing Keg Tapper and Beer Keg. a. The Sankey type keg tapper supplied with beer dispenser is the most widely used in the United States. However, some other type keg tappers, such as Golden-Gate, European Sankey or Hoff-Stevens are still being used. Before installing keg tapper, check with your beer distributor to make sure that the Sankey type keg tapper can be used. If you need a keg tapper other than Sankey type, it is recommended to purchase the tapper you need from your beer distributor keeping the Sankey type keg tapper for future use because the Sankey system is becoming more widely used. If you wish to have the Sankey type keg tapper exchanged with another type keg tapper, please return collect the Sankey type keg tapper to the address below specifying the type of keg tapper you need: Sanyo E & E Corp. 2001 Sanyo Avenue San Diego. California 92173 A'r-rN: Customer Service Dept. b. Make sure shutoff valve on CO2 regulator is in closed position. Connect pressure tube to nipple of keg tapper (use hose clamp). Connect beer tube from draft arm to keg tapper (fasten securely with washer and wingnut). c. Make sure that beer faucet and keg tapper are in closed position, then tap a keg. Open keg tapper valve. (For more detailed procedures for Items B and C, refer to attached leaflet.) d. Make sure the keg is properly tapped, then open shutoff valve on CO2 regulator. To install beer keg into cabinet follow the steps below (see Fig. 3). ,• Wet the surface of keg supports (wooden plates) • Lean keg supports on the front bottom edge of cabinet. • Place keg on supports supporting keg by hands. • Push the upper part of keg to stand in upright position then slide keg supports into cabinet. • Make sure that keg and beer tube do not touch cold plate and that keg and keg supports are properly positioned not to interfere with door dosing. e. Release air caught in draft arm assembly by opening beer faucet until foam appears. Now dispenser is ready to us. -3 REPLACING EMPTY KEG Close shutoff valve on CO2 regulator then remove keg tappel from empty keg. To tap a new keg, follow the procedures C, D and E of "Installing Keg Tapper and Beer Keg." Keg j. Support Cabinet Bottom (1) Lift to upright i / / I / (2) Slide into cabinet. Fig. 3 OPERATION Place drip tray under beer faucet. To dispense beer, open beer faucet quickly all the way. If you have any trouble with beer, refer to "Draught Beer Facts" book. The recommended pressure for the CO2 system is 8-10 Ibs. CLEANING 1. To maintain good-tasting beer, periodical cleaning of beer system is required. Complete cleaning kit is provided for your convenience. Refer to the instructions included in cleaning kit. 2. To clean cabinet inside and outside, mix 2 tablespoons baking soda with 1 quarter warm water, or use mild soap. Never use strong cleanser, scouring powder or pads. Do not put the drip tray in dishwasher, it is not dishwasher safe. Vacuum the tubing on outside back twice a year. To provide protective care of the painted finish: Regular applications of wax or polish provide vital protection against rust. Waxing cleans the surface and seals out moisture and other contaminants. Use a wax or polish that is suitable for appliances. Apply the wax or polish when the refrigerator is new and then at least twice a year. Between waxings, clean the cabinet with the same polish or with a CLEAN soft cloth dampened with a mild household detergent. Rinse with a CLEAN lightly dampened cloth and DRY thoroughly. PARTS LIST MODEL 564.8815022 CAUTION: Use Kenmore part number on all orders, not the illustration number. Illus. No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. Part No. 300746 300747 300748 300308 300749 300459 300750 300751 300752 300140 300753 300459 300754 300755 300756 300757 300758 300759 300308 300760 300165 300463 300308 300308 300761 300762 300141 300308 300308 300763 300764 300308 300765 300766 300767 300768 300769 300770 300771 300308 300772 300103 300308 300096 300100 300479 Description Door Liner Door Gasket Door Tapping Screw Hinge, Upper Bolt BeerTube Insulation Beer Tube Sleeve Evap. Bracket (4) Machine Screw Hinge, Lower Bolt Wheel Caster (4) Machine Screw Cabinet Assembly Power Supply Cord Cord Bushing Clamp Tapping Screw Thermostat Bracket, Thermostat Machine Screw Tapping Screw Tapping Screw Back Cover Cold Control Dial Control Knob Tapping Screw Tapping Screw Bracket, Top R...

Download now

Please, enter two numbers from picture: