Votes - , Average rating:
(
)
)
Manafacture: Liebherr
File size: 1.57 mb
File name: 68534d7a-fe2c-4f2a-bae4-06b4bf02b940.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
3. Slide brackets (4) onto the side installation frames (5) from above and below. 4. Using the frame (5), screw the brackets onto the side wall*. 5. Slide the side installation frames (5) upwards until they are in contact with the underside of the ventilation grille. 6. Secure the side frames with the adhesive section (7) to prevent them from sliding down. Remove the protective film and affix the adhesive sections over the upper brackets on the handle and hinge sides. Figure 16 A delight in freshness 14 WF1051 / EWTNes 2956 INSTALLATION Turn clockwise for up and counterclock-wise for down. For the rear use the adjusting bolt (2). Turn clockwise for down and counterclockwise for up. Maximum adjustment: 19/64" (15 mm). 3. Figure 18: Align the appliance at the side with the cabinet side panel and attach it with screws (1). - Cover the screws with cover caps (2). 4. Fit the ventilation grille at the bottom [(3) if the door is hinged on the left, (4) if it is on the right]: Secure the ventilation grille so that it touches the floor and then adjust it using the slots. Figure 18 Figure 17 1. Carefully slide the appliance into the cabinet until the ventilation grille touches the surrounding kitchen cabinet. 2. Align the appliance until it is parallel with the surrounding kitchen cabinet. Use the open- end wrench 10 mm (3) to adjust the feet at the front. - Figure 17: Connect the appliance to the main power supply. - If the appliance is equipped with an IceMaker, establish the connection for the water supply. See “IceMaker, Water Connection”. 1. 2. 1 2 2 3 3 3 10 spanner 8 spanner 2 2 3 5 5 5 5 1 4 3. 4. A delight in freshness WF1051 / EWTNes 2956 15 INSTALLATION 1. At least 31 square inches (200cm ) 1 2 1 1/2” (38mm) 20 3/4” (527mm) 2 2 1 5 1/2" (13 mm) 24" (609.6 mm) 3-11/16" (93,7 mm) The following ventilation cross-section and distances must be observed: - There must be a ventilation space of at least 31 square inches (200 cm.) per appliance in the cabinet plinth and under the cabinet top panel. - The depth of the ventilation duct at the rear of the cabinet must be at least 1- 1/2" (38 mm). Alternatively: 1. For built-in appliances without ventilation grilles and only with an installation frame, ventilation must take place through the ventilation duct at the rear of the cabinet. Built-in appliances with an installation frame: • Figure 19: - Screw the complete installation frame (2) to the appliance. 2. Built-in appliances with a wooden ventilation grille: Figure 20: Cut out the wooden trim for use as a ventilation grille using the enclosed template. - The required ventilation cross-section must be at least 31 square inches (200 cm.) when a single appliance is installed, which corresponds to template “small” (If you install two appliances side-byside, the cross-section must be at least 62 square inches, (400 cm.), which corresponds to template “double-size;” for more information see “Side-by-Side Installation”). • Remove the attachment bracket (2) from the installation frame and screw it to the appliance (1) from underneath. Place the wooden ventilation grille (5) on the appliance, align it in the center and secure it from the rear using the attachment bracket (2). Figure 19 Figure 20 BLOCKING FOR SAFETY Figure 21: Secure the appliance in place so it does not tip forward when the fully stocked door is opened. 1. Measure the distance from the floor to the upper edge of the unit. 2. Locate and mark two wall studs (1) against the wall where the appliance will be located. The space between the unit top and the bottom of the brackets must not be more than 1/4" (6.4 mm). 3. Make sure the screws (2) extend a minimum of 1" (25.4 mm) into each of the wall studs. 4. Make sure the anti-tip brackets (3) extend at least 3" (76.2 mm) over the unit and are securely in place. IMPORTANT The anti-tip brackets can be installed in either direction or closer together. Always position the anti-tip brackets as wide apart as possible, but make sure they are anchored to two studs. 5. Using the adjustable roller base, raise the unit until it makes contact with the brackets. Make sure the front levelers are firmly on the floor to prevent the appliance from tipping forward. IMPORTANT If your unit is positioned in between the wall studs, a board can be secured to the wall. Make sure the board is secured to the studs with screws that will penetrate into the studs a minimum of 1" (25.4 mm). The board should be a minimum of 1" x 6" (25.4 mm x 152.4 mm) and long enough to secure both ends to the wall studs. 1 2 min 3" 3 Figure 21 A delight in freshness 16 WF1051 / EWTNes 2956 ICEMAKER Water Connection - Figure 22 Please read the first three points of the safety instructions and warnings before connecting the appliance to the main water supply. • The water pressure must be between 21.887.0 psi (1.5-6 bar). Use a 1/4" OD copper line to connect the water supply to the solenoid valve. Allow extra length to the water supply line to provide slack for ...