Votes - 3, Average rating: 4.3 ( )

Manafacture: RCA File size: 111.35 kb File name: 7d633c05-d43b-45ea-8237-cee10e0a7987.pdf Language of manual:

Pressing No will discard the changes. The input volume can also be controlled during recording by using the Vol Up and Vol Down buttons. 10 Microboards CopyWriter Live CD Tools The CD Tools menu item allows you to close an open Audio CD. It also allows you to erase a CD-RW disc. Press Yes/Setup when you have selected the CD Tools entry on the Setup Menu. There are 3 options under the CD Tools menu: Close Disc In order for a recorded disc to play back correctly in other players, the disc must be closed. If you press Stop to stop your recoding, then the disc is closed and can be played on other playback devices. If you press Pause while recording a disc, recording will stop, but the disc is not closed. Playback of this disc is only possible on the CopyWriter Live system. If you press Pause while recording a project and then decide you do not want to record any additional information to that CD, you can close the disc by selecting Close Disc in the CD Tools Menu. Press the No button until you reach the drive you wish to close, either the left or right drive. Press Yes/Setup to start the process. The message Closing Disc will flash until the disc is closed. After the closing of the disc is complete, press the Yes/Setup screen to return back to the CD Tools menu. Quick Erase/Full Erase The CW Live can erase CD-RW media. You have the choice of doing a quick erase or a full erase. Just place the CD-RW disc in either or both drives and press the Yes/Setup button at the left or right drive. The message Erasing CD will flash on the display until the process is complete. Once the erase is completed, press the Yes/Setup button to go back to the CD Tools menu. Track Extraction This menu option allows you to extract tracks from one master and burn them to a blank disc. To use this feature, follow the directions below: 1. Press Yes/Setup at the Track Extraction menu selection in the Setup menu to begin. 2. The display will read Extraction OK? Press Yes/Setup, and the drives will eject. Place the master disc in one drive and a blank in the other and close the drive trays. The master will run through a track analysis. It does not matter in which drive the master is placed. 3. After the master is analyzed, the display will read EXTRACT THE TRK?, followed by TRACK 01/XX, where XX is the number of tracks on the master. Press Yes/Setup to select the track or No to not select the track. 4. Repeat step 3 until all tracks on the master have been offered for extraction. 5. After the last track on the master, the display will read End Extraction? Press Yes/Setup to begin burning the selected tracks to the blank disc. Press No if you wish to change your selections; you will run through steps 3-5 again. 11 Microboards CopyWriter Live 6. After the selected tracks have been burned, the display will read Next Master? Press Yes/Setup, and the master drive will be ejected to allow you to insert a new master. Close the tray, and repeat steps 3-5 for the new master. 7. When you have burned the last track to the disc, answer No to the Next Master? query. The disc will then be closed automatically, ejecting when complete. You cannot put more tracks on the disc than the disc will hold. If the capacity of the disc will be exceeded by selecting a track, you will not be able to select that track. Note: If you wish to rearrange the tracks on a single master, you can do so by selecting tracks off the same master multiple times. You will need to plan the order of the tracks, as you cannot reverse the orders of tracks during a single master track extraction sequence. For example, you wish to place all the even numbered tracks in order on the new disc first, followed by the odd numbered tracks in order. You would need to select the even numbered tracks from the master the first pass, then burn to the blank disc. When asked for the next master, press Yes/Setup but keep the master in the tray. Select the odd numbered tracks, burn the tracks, then answer No at the next master prompt to close the disc. Beep This setting allows you to turn on or off the button beep. Use the Vol Up or Vol Down button to turn the beep on or off. Press Yes/Setup when done. System Info System Info allows you to view the current firmware version installed on the CopyWriter Live. Press Yes/Setup at the System Info menu selection in the Setup menu to review the Firmware Version and Hardware Version. Press No to review the drive make, model, and firmware. Press No to have the option of returning to the Setup menu. System Update The CopyWriter Live system can be updated with a CD. If there are changes in the firmware, such as improved features, bug fixes, etc., the system can be updated using the System Update feature. In the Setup menu, press the No button until System Update is selected. Press the Yes/Setup button and the left drive will eject, prompting you to place the firmware disc in the drive with the message Insert Program Disc. Place the disc in the drive and close the tray...

Download now

Please, enter two numbers from picture: