Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
1 MB2186 O/M.QXD 8/12/02 11:22 AM Page 2 LOCATION OF CONTROLS FRONT REAR 1 23 4 11 12 13 14 15 5 16 6 7 17 8 9 10 1. MIC (Microphone) Jack 10. Battery Compartment 2. EAR (Earphone) Jack (Rear of unit) 3. VOLUME/VAC Mic 11. Built-in Microphone (Top Sensitivity Control of unit) 4. VAS (Voice Activation) 12. PAUSE ON/OFF Switch ON/OFF Switch 13. REC (Record) Button 5. Microcassette 14. PLAY Button Compartment 15. REW (REV)/F.F Switch 6. Tape Counter Reset Button Button 16. Stop/Eject Button 7. Tape Counter 17. TAPE SPEED (2.4/1.2) 8. REC/BATT Indicator Switch 9. DC 3V Jack 2 + - MB2186 O/M.QXD 8/12/02 11:22 AM Page 3 POWER SOURCES BATTERY INSTALLATION Open the battery compartment and insert two (2) "AA" size batteries (not included) following the polarity diagram. Put the battery compartment cover back into place. NOTE: The REC/BATT indicator will brightly light during recording when batteries are fresh. When they are weak, it will light dim. BATTERY PRECAUTIONS Follow these precautions when using batteries in this device: + — + — 1. Use only the size and type of batteries specified. 2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device. 3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones. 4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. 5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer’s directions.) DC JACK + - To use this unit with an external AC adapter (not included) having 3V and a negative center pin, insert the AC adapter’s plug into the DC 3V jack on the unit. The batteries will be disconnected when the AC adapter is connected. 3 MB2186 O/M.QXD 8/12/02 11:22 AM Page 4 OPERATION TO PLAY A PRERECORDED MICROCASSETTE TAPE 1 2 Press the Stop/Eject button and insert a microcassette tape with the side to be played facing you and the exposed tape facing the right. Close the Cassette Compartment. Slide the TAPE SPEED switch to the tape speed used when recorded. Set the VOLUME/VAC Mic Sensitivity control to minimum. 3 Press the PLAY button . to start playback and adjust the VOLUME/VAC Mic Sensitivity control . as desired. To stop the tape before it reaches the end, press the Stop/Eject button .. 1 2 3 4 EARPHONE JACK For private listening, connect an earphone (not included) to this jack. The speaker is automatically disconnected when the earphone plug is inserted in the jack. 4 MB2186 O/M.QXD 8/12/02 11:22 AM Page 5 OPERATION TO FAST REWIND/REVIEW A MICROCASSETTE TAPE 21 2 1 2 1 To rapidly rewind a microcassette tape in the Stop mode, slide the REW (REV)/F.F switch . to the REW (REV) position. Press the Stop/Eject button . when you reached the desired position. To rapidly review a microcassette tape, press the PLAY button . and then slide and hold the REW (REV)/F.F switch . to the REW (REV) position. You will then hear the microcassette play at fast speed. Release the switch to resume normal playback. TO FAST FORWARD/CUE A MICROCASSETTE TAPE 1 2 1 21 2 To rapidly forward a microcassette tape in the Stop mode, slide the REW (REV)/F.F switch . to the F.F position. Press the Stop/Eject button . when you reached the desired position. To rapidly cue a microcassette tape, press the PLAY button . and then slide and hold the REW (REV)/F.F switch . to the F.F position. You will then hear the microcassette play at fast speed. Release the switch to resume normal playback. 5 MB2186 O/M.QXD 8/12/02 11:22 AM Page 6 OPERATION TO PAUSE A CASSETTE TAPE This unit can pause the microcassette while Recording, Playback, Rewind or Fast Forward To pause Recording, Playback, Rewind or Fast Forward, slide the PAUSE switch to the ON position. 1 To resume, slide back to the OFF position. 2 TAPE COUNTER The tape counter is helpful in locating particular portions of the tape. 001 1 000 2 The tape counter will count up or down when playing, recording, fast forwarding or rewinding a microcassette tape. To reset the counter, press the Tape Counter Reset button; the counter will reset to “000” TAPE SPEED SWITCH Set the one of the following positions: 2.4: 1.2: NORMAL SPEED: Compatible with most single-speed microcassette recorders. This setting has the best sound quality. LONGER RECORDING: This will allow double recording time, but the sound quality will be less. 6 MB2186 O/M.QXD 8/12/02 11:22 AM Page 7 OPERATION NORMAL RECORDING This unit is capable of recording only when sound is heard. To use this feature, see the next page. For normal recording, follow steps below. 1 2 Press the Stop/Eject button and insert a microcassette tape with the side to be played facing you and the exposed tape facing the right (and the Erase Prevention Tab intact, see note below). Close the Cassette Compartment. Slide the TAPE ...