Votes - 3, Average rating: 4.7
(
)
)
|
manual abstract
Push the wheel arms, with the bend toward the centre of the carrier and wheel dropouts pointing downwards, into each VersaWing 2.0. DANGER Make sure that the wheel arms are correctly attached to the carrier. Incorrect attachment may lead to loss of the front wheel during travel and this may lead to an accident. Press the small button in for each and push the wheel arms into the VersaWing 2.0 until the large button engages Guide the quick-release axle through the wheel axle and screw (Figures 1 to 3). on the nut. Both skewer springs must be located on each side so that the narrow side points towards the centre of the hub. Tip the carrier backwards and put it down on the handlebar. Insert the wheel in the axle dropouts. Close the quick- release lever. In order to ensure that the hub is clamped sufficiently in the axle dropouts, the quick-release lever must begin gripping as it moves from the open to the middle position, and approaching the closed position you should clearly feel resistance as you tighten. If it is too easy or too difficult to move the quick-release, tighten or loosen the lock nut on the other side of the hub to adjust. If you don’t feel confident operating the quick-release skewer, please ask your specialist retailer for assistance. DANGER Always make sure that the quick-release is correctly installed. An incorrectly tensioned quick-release may lead to the rear wheel coming loose, resulting in accidents. DANGER When using the carrier as a Jogging Stroller, always put the safety wrist strap, which is fastened securely on the left rear upper frame tube, around your wrist. This prevents the carrier from accidentally rolling away. To correct directional trueness (ie. The carrier not rolling straight): The dropouts of the wheel arms are screwed on and their holes are slotted. After loosening both screws, the dropout can be moved. This is possible on both the right-hand and the left-hand side dropout. If the Jogging Stroller is pulling to the right, the dropout on the right-hand side must be moved forwards, and the one on the left-hand side backwards (or vice versa). WARNING Please ensure that your child does not stand on the wheel arms when entering or leaving the carrier. If at any time you stop, do not allow anyone to sit on the wheel arms. Applying a load on either wheel arm may result in the aluminium axle sockets working loose. Travelling 7. The Strolling Kit Weight distribution DANGER So as to prevent it from tipping backwards, the storage compartment at the rear of the carrier may not be loaded with excessive weight. Carry out the following check: push downwards on the handlebar by about 150 mm. The carrier should return to its original standing position and should not tip backwards. The assembled Stroller (CTS Ready Chassis + Strolling Kit) Supplied as standard Strolling Kit: 2 x 8” stroller wheels Safety instructions for use as a Stroller • Please make sure you read the safety instructions in the “Safety” section at the beginning of this Owner’s Manual. • Before each journey check that all components are properly fitted, particularly the stroller casters and the handlebar. • Do not park the carrier on roads or other places which are on an incline. • If you leave the stroller stationary, always secure it with the parking brake. • When pushing the stroller, always put the wrist safety strap around your wrist. • Inline skating with the stroller is not permitted. • The foot activated parking brake is not suitable for deceleration of a moving carrier. • So as to prevent it from tipping backwards, the storage compartment at the rear of the carrier may not be loaded with excessive weight. Carry out the following check: push downwards on the handlebar by about 150 mm. The carrier should return to its original standing position and should not tip backwards. Performance characteristics Inline skating with the Stroller is not permitted. Assembly To attach the stroller wheel, press the plastic button on the side of the VersaWing 2.0 until it can go no further. Then, from below, insert the upward pointing caster shaft of the stroller wheel into the vertical hole of the VersaWing 2.0 until it can go no further. If you want to convert the carrier from Stroller to another CTS Conversion Kit, you can store the stroller wheels on the top of the VersaWing 2.0 . To attach them proceed as described above. The caster fork arms should point forwards. DANGER Always make sure that the stroller wheels are fully engaged and locked. Travelling Weight distribution Release the plastic button. This now clicks back towards the outside, resulting in locking of the attachment axle of the stroller wheel. DANGERAlways make sure that the stroller wheels are properly and fully engaged and locked. To check this pull the stroller wheels up and down in a vertical direction. Make sure that the plastic locking button has fully clicked back. Incorrect assembly may lead to accidents. DANGERSo as to prevent it from tipping backwards,...
Other models in this manual:Stroller - Corsaire XL (2.46 mb)