Login:
Votes - 2, Average rating: 3.5 ( )

User manual Bumbleride, model Queen B

Manafacture: Bumbleride
File size: 2.58 mb
File name: queen-b-manual-x.pdf
Language of manual:enfr
Free link for this manual available at the bottom of the page



manual abstract


THE WARRANTY CARD MUST BE RETURNED WITH PROOF OF PURCHASE IN ORDER TO ACTIVATE THE WARRANTY PERIOD. You may also register your stroller online at This warranty does not cover damage caused by normal wear and tear, neglect, accidents, lack of maintenance or damage caused by parts not manufactured by Bumbleride. All warranty claims must be made directly to the authorized retailer from whom the product was purchased. All costs associated with shipping and handling is the responsibility of the customer. Upon receipt of the product, Bumbleride. or its authorized repair center will arrange for inspection of the item. If the problem is due to defective parts or defective workmanship on behalf of Bumbleride., Bumbleride will repair or replace the product at Bumbleride's option. If the product is not covered under the original warranty, the customer will be responsible for all expenses associated with the service provided. I 2 OPERATING MANUAL CONTENTS 1 Important Safety Instructions 1 Warnings 2 Safety Standards 2 Limited Warranty 3 Box Contents 4 Opening Pram 4 Assembling Wheels 5 Operating Brake 5 Attaching Seat to Chassis 6 Attaching Canopy 6 Attaching Front Bumper 6 Attaching Footmuff 7 Using the Seat Harness 7 Adjusting Backrest 7 Adjusting Footrest 8 Adjusting Handle 8 Attaching Accessory Cup Holder 8 Folding Pram 9 Stroller Diagram BOX CONTENTS CHASSIS 3 I Bumbleride 1.800.530.3930 ¡nfo@bumbleride.conn SAFETY BELT " CUP HOLDER t/t CANOPY REAR WHEEL COGS (4) % % %% BUMPER BAR REAR WHEEL AXLE PINS (4) FOOTMUFF OPENING PRAM Unfold and extend the chassis by pulling up on the handlebar [1]. Ensure that the chassis locks and clicks into position [2]. t,n ** Uji 2=33 ■w *1 .1* WARNING: Always verify that the main locking devices are engaged correctly before using your pram. ASSEMBLING WHEELS Attach the wheels by squeezing the hubcap release button and sliding wheel onto the axle as far as it can go [1]. Release button so wheel clicks into position and pull on the wheel to ensure it is securely attached to the axle. Locate the pull lever on the front left side of the pram to lock the steerable wheels. Push the lever down and move to the desired setting. Release lever to click into place [2]. To remove wheels, squeeze hubcap release button and slide wheel off of axle. WARNING: Pull on each wheel to ensure that it is locked before use. OPERATING BRAKE Apply brake bar by pushing down with foot. Make sure it is securely locked in place. Ensure brake is applied when parking the stroller. Release by lifting bar with foot. 5 I Bumbleride 1.800.530.3930 ¡nfo@bumbleride.conn ATTACHING SEATTO CHASSIS Apply brake by pushing down on brake with foot. Lift the seat by the armrests to locate the two metal studs on the side of the seat (one on each side). Insert the two studs into the slots on either side of the chassis [1]. Lower the seat onto the chassis, pull open the two locks (one on each side) and drop the two studs into them. Make sure both locks are closed [2]. 1 2 ATTACHING CANOPY Insert each end of canopy into the plastic holders located on either side of the frame [1]. To remove, squeeze clips on both ends. ATTACHING FRONT BUMPER Line up bumper ends and slide into armrest slots until they click into place. Secure middle strap around bumper and secure with snaps. To detach bumper, squeeze levers on seat frame under armrest slots and gently pull out to remove. You may need to slide each side out separately using small movements. ATTACHING FOOTMUFF Slide the footmuff over the footrest and seat. Unsnap the canopy from either side of the frame and snap the footmuff onto the canopy frame on both sides. Finally snap the canopy onto the footmuff snaps. I 6 USING THE SEAT HARNESS Insert buckles [A] and [B] into either side of the buckle housing [C] until they click into place securely. Carefully adjust the harness straps to snugly fit your child by adjusting the sliders located on all shoulder straps, waist straps and the central front strap. To open the harness, squeeze the buckle prongs and pull away from the buckle housing [C], WARNING: ALWAYS USE SAFETY HARNESS WHEN CHILD IS SEATED IN THE STROLLER. Bumbleride 1.800.530.3930 ¡nfo@bumbleride.conn ADJUSTING BACKREST To lower the backrest, lift the lever on the rear of the backrest to adjust to the desired position. To raise, simply push the backrest up. WARNING: Infant may slip into leg openings and suffer injury. WARNING: Never use in reclined carriage position unless the footmuff is attached or the foot rest is in its fully upright position. ADJUSTING FOOTREST Simply lift the footrest to adjust to a horizontal position. To lower the footrest, simply pull on the corresponding levers beneath the foot rest simultaneously and lower to the desired position. ADJUSTING HANDLE POSITION Press the buttons on both sides of the h...


Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category