Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
Requires one, size “D” (LR20) alkaline battery (not included) in the Requires three, size “ AA” (LR6) alkaline batteries (not included) in the toy bar. Slide switch to or AND bat mirror for sounds and lights! WARNINGS To prevent serious injury and/or falls: • Never use on any elevated surface. • Never use as a carrier or lift while child is seated. • Always use the restraint system. • Never leave child unattended. • Never use as a car seat. • Never use with a child able to sit up unassisted. WARNING CONSUMER INFORMATION Occasionally a consumer may experience a problem with one of our products. If this should happen, please call us toll-free, rather than return this product to the store. Usually, we can solve the problem over the telephone or send you replacement parts. Please call Fisher-Price ® Consumer Affairs, toll-free at 1-800-432-KIDS, between 8 AM - 5 PM EST, Monday through Friday. Hearing-impaired consumers using TTY/TDD equipment, please call 1-800-382-7470. Or write to: Fisher-Price® Consumer Affairs 636 Girard Avenue East Aurora, New York 14052. 2 3 PARTS #8 - 32 x 1/2" Screw - 2 Shown Actual Size 2 Flowers Butterfly 2 Paddles Toy Bar Pad Footrest Wire Seatback Wire Right Base Wire Left Base Wire Base Connector #8 - 32 Nut - 2 Shown Actual Size 4 ASSEMBLY • Place the base connector on a flat surface as shown. • Position the left and right base wires as shown. Note the locations of the red marks on the left and right base wire. • Fit the left base wire into the base connector. • Fit the right base wire into the base connector. • Make sure both red marks on the base wires are covered by the base connector. 1 Base Connector Red Right Base Marks Wire Left Base Wire This package contains small parts. Adult assembly is required. CAUTION 6 ASSEMBLY • Insert a screw through the outside of each plastic cover and tighten with a Phillips screwdriver. Do not over-tighten. • Pull up on the seat back wire to be sure it is secure. If you can remove either end of the seat back wire, you have not assembled it correctly. Remove the screws, re-read and repeat Assembly steps 3 and 4. 4 #8 x 32 Nut Pull Up Protruding Side 3 5 • Position the footrest wire so that the soothing unit is upright. • While flexing the base wires toward each other, hook the footrest wire onto the ends of the base wires. • Push the footrest wire down completely, below the red marks on the base wires. ASSEMBLY 2 Base Wire Red Mark Base Wire Soothing Unit Footrest Wire Red Mark • Position the seat back wire with the toy bar sockets upright. • Fit the seat back wire completely onto the base wires, so that each end covers the red mark on each base wire. • Make sure the plastic covers on the seat back wire cover the red marks on the base wire. Red Mark Plastic Cover Plastic Cover Base Wire Toy Bar Socket Seat Back Wire • Fit the nut (so that the protruding side is outward) into the hexagonal opening on the inside of each plastic cover. ASSEMBL Y ASSEMBLASSEMBLY • Wrap the elastic straps on the pad flaps around the outside of each plastic cover. • Hook the elastic straps to the peg on the inside of each plastic cover. 6 Elastic Strap Elastic Strap Inside View Elastic Strap Plastic Cover Plastic Cover Plastic Cover Peg • Position the pad with the ruffle upright. • Fit the upper pocket on the back of the pad onto the seat back wire . • Fit the restraint belts through the slots in the pad . 5 Seat Back Wire Slot Pad Restraint Belt A B B C A B C • Lift the footrest wire. Fit the lower pocket on the back of the pad onto the footrest wire . Lower the footrest wire. Hint: Before assembling the lower portion of the pad to the footrest wire, you may want to install the battery in the soothing unit. Please see the next section (page 10, Battery Installation) for instructions. 78 ASSEMBLY • Fit the toy bar plugs into the socket in each plastic cover. • Snap the paddles to the toy bar wire. • Fit the tab on the butterfly into the slot in the paddle. Paddle Paddle Butterfly Flowers Plugs Sockets Wire Toy Bar • The flowers can be attached to the paddles. Hint: Twist the ends of the flowers apart to attach them to the paddles. Assembly is now complete. • The toy bar is removable. Simply pull up to remove. 9 BATTERY – 1.5V “D” (LR20) + SHOWN ACTUAL SIZE Battery Compartment Door Soothing Unit • Lift the footrest wire. Remove the pad from the footrest wire. • Insert a coin into the battery compartment door and pry the battery compartment door off. • Insert one, size “D” (LR20) alkaline battery, as indicated inside the battery compartment. Be sure to place the battery on top of the ribbon. Hint: For easy battery removal, simply lift the ribbon. • Replace the battery compartment door and be sure it snaps securely closed. • Replace the bottom of the pad onto the footrest wire. • Lower the footrest wire. 10 BATTERY – 1.5V x 3 “AA” (LR6) + SHOWN ACTUAL SIZE Toy Bar • Locate the battery compartment door on the back side of the toy bar. • Loosen the screw in the battery co...