DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. 2 • Locate the leg with tape on it. • Locate the matching tape covering the socket in the base. • Align the tab on the leg with the slot in the base socket. • Insert and “snap” the leg into the base socket. 4 4 4 4 4 4 3 3 3 3 3 3 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 • Locate the upper rail with leg and tape on it. • Remove the cardboard attached to the wire connector.Throw the cardboard away. • Pull the wire connector out from the hole in the bottom of the leg. 2 Tape Base Socket Wire Connector 2 Tape Upper Rail with Leg Cardboard Leg • Position the upper rail with leg so that the leg with tape is over the base socket with matching tape. • Insert and “snap” the leg with tape into the socket with matching tape. • Now, firmly push the upper rail above the leg with tape on it.Make sure you hear a “snap”. • Firmly push the upper rail above the leg with tape on it. Make sure you hear a “snap”. • Pull up on the upper rail to be sure it is secure. 2 2 2 4 4 4 4 4 4 2 2 2 1 1 1 3 3 3 3 3 3 2 2 2 2 2 2 3 Upper Rail with Leg Base Socket PUSH PUSH 2 Tape 1 1 1 2 2 2 3 3 3 4 4 4 4 4 4 4 4 4 3 3 3 3 3 3 4 Base Socket Base Socket • Locate the legs with tape on them. • Locate the matching tape covering the sockets in the base. • Align the tabs on the legs with the slots in the base sockets. • Insert and “snap” the legs into the base sockets. 3 4 4 Tape 3 Tape 5 Assembly • Fit the upper rail onto the legs, as shown. • Push down firmly above each leg until, you hear the upper rail “snap” into place on each end. • Pull up on the upper rail to be sure it is secure. Note: Remove the tape on the legs and around the base sockets.Throw the tape away. 1 1 1 2 2 2 3 3 3 4 4 4 5 • Fit the “T” end of the strap on the trumpet through the slot in the upper rail. Pull the trumpet to be sure it is secure in the upper rail. 6 Upper Rail Trumpet Upper Rail Slot Hint: You may want to use the end of a slotted screwdriver to push the “T” end of the strap through the slot. PUSH PUSH “T” End • At an angle, fit the single tab on the bell into the slot in the upper rail. • Now, push and “snap” the other two tabs on the bell into the slots in the upper rail. • Position the mirror so that it is toward the inside of the product. • Insert and “snap” the tabs on each end of the mirror into the matching slots in the upper rail. 7 8 Bell Upper Rail Slot Mirror Slots PUSH 6 Assembly • Fit the tray underneath the mirror, into the upper rail, as shown. • Insert and “snap” the ends of the maraca and tambourine into the holes in each end of the upper rail with keyboard. 10 9 Tray Maraca Tambourine • Locate the seat lock buttons on the underside of each upper rail. • Fit the groove on each side of the seat base onto the tracks on the upper rails. 12 Seat Lock Button Track Seat Base Groove • Turn the seat base upside down on a flat surface. • Insert and “snap” a roller into each clip on the edge of the seat base, as shown. • Repeat this procedure to assemble the remaining two rollers to the other side of the seat base. 11 Seat Base Roller Roller Clip Clip 7 • Position the seat ring so that the inside (ribbed side) is up and the star marking is toward you. • Fit the red slots on the pad to the seat ring pegs on either side of the star marking, as shown. Assembly • While pushing a seat lock button on one of the upper rails, slide the seat base over it. • Now, push the seat lock button on the other upper rail and slide the seat base over it. • Push the seat base so that it is positioned in the center of the product. You should hear a “snap” on each side. 13 Seat Ring Ribbed Side Red Slot Red Slot Marking 14 Pegs Marking PUSH • Pull the pad through the seat ring and wrap the pad around the outside of the seat ring. Seat Ring Seat Ring Pad Pad 15 8 • Fit the other six slots on the seat pad to the corresponding pegs on the seat ring. • Tuck the seat pad behind all four rollers. Assembly 16 Peg 2 Peg 3 Peg 4 Peg 5 Peg 6 Roller Roller Roller Roller Peg 1 • Insert and “snap” the seat with pad into the hole in the seat base. • Pull up on the seat to be sure it is secure. 17 Seat with Pad Hole in Seat Base • Tip the end of the product up and locate the wire connectors. • Fit the connectors together. If they will not go together easily, do not force them together.Turn one or the other connectors over, and try again! One-time assembly is now complete. 18 Connectors 9 Installation • Locate the battery compartment door under the upper rail with keyboard. • Loosen the screw in the battery compartment door with a Phillips screwdriver. Remove the battery compartment door. • Insert three “C” (LR14) alkaline batteries, as indicated inside the battery compartment. • Replace the battery compartment door and tighten the screw with a Phillips screwdriver. Do not over-tighten. Battery Compartment Door Batteries may leak fluids that can cause a chem...