Votes - 3, Average rating: 4
(
)
)
|
manual abstract
4. 54 11 11 60 59 55 54 58 23 23 Assemble lanyard (26) to locking pin (27) as shown (FIG A). Attach covers (35) onto pole mount bracket (28) with carriage bolt (19) and nut (11) as shown. IMPORTANT! Loop end of pin lanyard (26) over carriage bolt (19) as it passes through the pole mount bracket (28) during this assembly. IMPORTANT! Indicator labels should be applied as close to holes as possible to prevent labels from being damaged during height adjustment. ID# M6011141 04/06 18 29 30 30 29 52 Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (27). 27 5. 6. Assemble backboard brackets (52) 52 using bolts (29), and nuts (30) as shown. 52 NOTE ORIENTATION 8. 8. Identify elevator tubes (33 & 34). 33Upper Elevator tube Toward Pole Toward Board 34Lower Elevator tube Toward Pole Toward Board Attach lower elevator tubes (34) and counter balance spring (36) to backboard support brackets (52) using spacers (53 & 56), bolt (57), and nut (21) as shown. Insert T-bolt (48) into rim bracket (61) then, attach that assembly to board using bolts (41) and nuts (21). 57 36 56 52 21 34 34 53 56 36 41 61 48 6148 21 19 04/06 ID# M6011141 9. 9. Attach upper elevator tubes (33) to backboard support brackets (52) using spacers (53), bolt (57), and nut (21) as shown. Tighten ALL Hardware from Steps 6-8 After this Assembly is Completed. IMPORTANT! 33 56 52 2153 57 33 56 57 56 56 2153 33 33 20 ID# M6011141 04/06 21 21 49 25 34 1 32 32 57 20 34 20 10. Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (25). 10. Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (25). 57 34 33 20 21 1 21 33 20 32 58 11. Install upper elevator tubes (33) to triangle plates (45) as shown. Install handle assembly to lower elevator tubes (34) using bolt (57), spacers (20), and nut (21) as shown. 57 34 34 20 20 Before going on to next step, set adjustable system assembly to the 10’ (3.05 m) setting. NOTE: 21 04/06 ID# M6011141 ID# M6011141 04/06 22 12. Install Rim to Backboard A. Fit rim (51) securely into bracket (61) as shown. Allow T-bolt (48) to slip through center hole in rim (51). B. Install reinforcement bracket (44) onto T-bolt (48) as shown. C. Install spring (46) onto T-bolt (48) as shown. D. Install special nut (47) and washer (45) onto T-bolt (48). E. Tighten special nut (47) until flush with end of T-bolt (48). 44 47 45 61 48 51 46 48 45 47 48 48 NOTE: ORIENTATION OF BRACKET 44 A. B. C. D. E. 23 04/06 ID# M6011141 33 36 21 33 58 14. Insert bolt (57) through left side upper elevator tube (33), then stretch spring (36) onto bolt (57). Insert bolt (57) through right side upper elevator tube (33) and secure with nut (21). 57 Peel protective 36 film from surface of acrylic backboard prior to use. NOTE: USE EYE PROTECTION WHEN INSTALLING SPRINGS. WARNING! 13. Install net (40). A. B. C. D. FILL BASE 15. Roll assembly to desired playing area. Fill base (8) with water (approx. 40 gallons) and snap base plugs (37) in place. 37 37 8 Sable SableSable Sand SandSand Arena ArenaArena (163 kg) (163 kg)(163 kg) WARNING! CAUTION NOTE WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. ADD TWO GALLONS (7.6 LITERS) OF NON-TOXIC ANTIFREEZE IN SUB-FREEZING CLIMATES. IF USING SAND: 2 GALLONS OF ANTI-FREEZE IS NOT REQUIRED 24 ID# M6011141 04/06 25 04/06 ID# M6011141 16. Install front cover (38) by lining up stand-offs along the tank struts. Insert a tie strap (39) through the top two and bottom two stand offs. Wrap tie straps around tank struts as shown and secure tightly. Trim excess of tie strap as shown in FIG.A. STANDOFFS 39 FIG. A FRONT COVER 38 ID# M6011141 04/06 26 2. A. While holding handle, remove pin (27). B. Move elevator up or down to desired height. C. Replace pin (27) full length to lock system at desired height. 27 A. B. C. 58 DO NOT ALLOW CHILDREN TO ADJUST HEIGHT. WARNING! 42 1. Apply Height Adjustment and Moving Label (42) to front of pole, where it is clearly visible. SECTION G: HEIGHT ADJUSTMENT AND MOVING LABEL 2 2 1 3 TO ADJUST BACKBOARD: 1. While holding handle, remove pin. 2. Move elevator up or down to desired height. 3. Replace pin full length to lock system at desired height. 511679 05/05 1 2 4 3 MOVING SYSTEM Adjust basketball backboard height to lowest position. While holding pole, rotate basketball system forward until wheels engage with ground. Move basketball system to desired location. Carefully rotate basketball system upright. 1. 2. 3. 4. 5. Check system for stability. HEIGHT ADJUSTMENT 46 10 pieds 3,05 m 10 Fu. (3,05 m) 10 pies (3.05 m) SSysteme portable FFRRAANNCCAAII Manuel d'utilisation DEUTSCH Service clientele N53 W24700 South Corporate Circle • Sussex, WI 53089 E.-U. ESPANOL Tragbares System Gebrauchsanleitung K...