Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
x .402 I.D. x 1.8 Long 10 1 202662 Bolt, 5/16-18 x 4-1/2 Long 52 2 201088 Board Bracket 11 11 203218 Washer, Flat, 5/16 x 7/8 O.D. 53 1 240017 Bolt, Hex Head, 1/4-20 x 2-1/4 Long 12 1 203220 Lock Nut, Nylon Insert, 5/16-18 54 1 206360 Bolt, Hex Head, 3/8-16 x 2.625 Long 13 1 200516 Vinyl, Bolt Cover, 5/16 55 1 203493 Lock Nut, Hex Center-lock, 1/4-20 14 2 203798 Bolt, Hex Flange, 5/16-18 x 1-1/2 Long 56 2 904821 Elevator Tube, Lower (Long) 15 19* 203100 Lock Nut, Whiz, 5/16-18 57 6 204847 Bolt, Hex Head, 1/2-13 x 9-1/2 Long 16 3 206327 Axle Rod, .461 O.D. x 4-1/4 Long 58 7 206340 Lock Nut, Hex Head, 1/2-13 17 3 226401 Wheel 4” Diameter 59 4 201682 Spacer, Black, .56 I.D. x .683 O.D. x 1.88 Long 18 1 200123 Upper Pivot Bracket 60 4 201611 Bolt, Hex Flange, 5/16-18 x 3 Long 19 1 200512 Bolt, Hex Head,3/8-16 x 3-1/2 Long 61 1 900741 Slam Jam Bracket, Black 20 14* 203232 Washer, 3/8 I.D., x 3/4 O.D. 62 2 203108 Bolt, Carriage, 5/16-18 x 2.5 Long 21 1 206252 Bolt, Hex Head, 3/8-16 x 1 Long 63 2 904807 Elevator Tubes, Upper (Short) 22 1 206948 Lower Pivot Bracket 64 1 207103 Pole Cap 23 1 203330 Bolt, Hex Head, 3\8-16 x 4-1/2 Long 65 1 201139 Bolt, Hex Head, 1/2-13 x 4.5 Long 24 2 200122 Hinge Tubes 66 2 201654 Triangle Plate 25 1 906608 Wheel Bracket 67 8 202862 Spacer, Plastic, 1/2 I.D., 1-1/4 Long 26 4 203103 Bolt, Carriage, 5/16-18 x 2 Long 68 2 204837 Spring 27 2 202808 Wheel 6” Diameter 69 1 203796 Bolt, “Tee” 3/8 - NC x 5 Long 28 1 206940 Axle, .461 O.D. x 21 Long 70 1 Rim 29 2 206938 Push Caps 71 1 203234 Bracket Reinforcement, Slam Jam 30 1 206956 Disc, Plastic, 5” O.D. x .0625 Thick 72 1 203472 Spring, Black 31 1 204839 Tinnerman Nut 73 1 203470 Washer, Flat 5/8 I.D. x 1-1/2 O.D. 32 1 904816 Inner Channel 74 1 203795 Nut, Special 3/8-NC 33 1 904815 Outer Channel 75 4 201611 Hex Flange Bolt 5/16-18 x 3 Long 34 1 204813 Handle, Height Adjustment 76 1 204281 Net 35 2 203217 Bolt, Carriage, 5/16-18 x 1.5 Long 77 1 211249 Label, Height and Moving 36 1 203679 Bolt, Hex Head, 3/8-16 x 2 Long 78 1 202438 Rope, Nylon Double Looped Tie Down 37 3 201124 Lock Nut, Hex, 3/8-16 79 1 203124 Stake, Tie Down 38 1 204814 Trigger, Height Adjustment 80 1 206219 Cap, Tank-Black 39 1 203589 Bolt, Hex Head, 5/16-18 x 1-1/4 Long 81 12 200121 Clip, Net Holder 40 1 201125 Ratchet Spring 82 1 200119 Front Cover 41 1 204809 Label, Accuheight 42 4 265601 Bolt, Carriage, 5/16-14 x 3-1/2 Long *You may have extra parts with this model WARRANTY CARD: Please remember to complete your product registration form on-line at: or mail-in the enclosed postcard. P/N 211260A 10/01 2 printed on recycled paper HARDWARE IDENTIFIEHARDWARE IDENTIFIER (CONTINUED) Item #7 (1) Item #20 (14)* Item #11 (11) Item #10 (1) Item #39 (1) Item #5 (1) Item #15 (19)* Item #35 (2) Item #8 (6) Item #12 (1) Item #13 (1) Item #14 (2) Item #16 (3) Item #21 (1) Item #23 (1) Item #26 (4) Item #36 (1) Item #37 (3) Item #19 (1) 10/01 P/N 211260A3printed on recycled paper P/N 211260A 10/01 4 printed on recycled paper *You may have extra parts with this model. HARDWARE IDENTIFIER (continued) Item #42 (4) Item #43 (2) Item #53 (1) Item #55 (1) Item #58 (7) Item #51 (2) Item #50 (1) Item #67 (8) Item #65 (1) Item #46 (2) Item #54 (1) Item #59 (4) Item #60 (4) Item #62 (2) #61 (1) HARDWARE IDENTIFIER (continued) #73 (1) #74 (1) #71 (1) Item #75 (4) #69 (1) #72 (1) printed on recycled paper 5 10/01 P/N 211260A INSTRUCTIONS IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL Install trigger return spring (40) to handle assembly (32, 33) as shown. 18. Attach Accuheight label (41) to outer channel (33). 19. Attach spring (44) to pins (43) and install pins (43) onto pole mount bracket (45). Attach other spring (44) to opposite side. NOTE: Gently enlarge eyelets of spring with pliers if springs do not fit over pins. WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS. 20. Install pole mount assembly and reinforcement bracket (47) with carriage bolts (46) to pole as shown. Tighten flange nuts (15) completely. 21. Push back sliding pin (43) as shown in Figure A to fit adjustable system assembly through pole mount assembly. Then attach spring covers (48 & 49) onto pole mount bracket (45) with bolt (50), and nut (15) as shown in Figure B. 22. Install spacers (51) onto backboard brackets (52) with bolts (53, 54) and lock-nuts (55, 37) as shown. 23. Assemble lower elevator tubes (56) as shown. NOTE : Tighten bolt (57) in lock nut (58) until flush (even) with lock nut’s outer edge. IMPORTANT! It is necessary for all parts to be installed for this mechanism to work safely and properly. NOTE: Test fit bolts into holes of brackets (52) and carefully rock them in a circular motion to ream out paint from holes if necessary 24. Bend brackets (52) to line up with holes in channel. Insert carriage bolts (62) into hole as shown. Tighten completely. Insert Tee-bolt (69) through Slam Jam Bracket (61) and attach to backboard with nuts (15) and bolt...