Votes - 3, Average rating: 4
(
)
)
|
manual abstract
• DO NOT position system near trampolines, diving boards, slides, or any play area equipment. System misuse could cause serious bodily injury. • Two pole assembly is for in-ground pool side use only. • Read and understand the warning label affixed to pole. • The life of your basketball pole depends on many conditions. The climate, placement of the pole, location of the pole, exposure to corrosives such as chlorine, pesticides, herbicides or salts are all important factors. • During assembly, if using a ladder use extreme caution. Two people are recommended for this operation. • Seat the pole sections properly (if applicable). Failure to do so could allow the pole sections to seperate during play and/or during transport of the system. • Climate, corrosion and excessive use or misuse could result in system failure. • Check tank regularly for leakage. Slow leaks could cause system to tip over unexpectedly. • If technical assistance is required, contact Huffy Customer Service Center. • Adult supervision is recommended when adjusting system. Most injuries are caused by misuse and/or not following instructions. Use caution when using this system. 200439 11/00 1 3 2 MOVING SYSTEM 1. While holding pole, rotate basketball system forward until wheels engage with ground. 2. Move basketball system to desired location. 3. Carefully rotate basketball system upright. 4. Reattach ground restraint and check system for stability. HEIGHT ADJUSTMENT A WARNING Backboard may rotate during height adjustment. B WARNING Do not adjust height of system in upright position. System must be in down position to adjust Rest unit on support table. Remove adjustment knobs (A) and carriage bolts (B) to extend or retract backboard and rim. Height adjustment from 7 1/2' to 10'. 15 3 04/03 P/N 211984A NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. For more information on assembly, placement, proper use and maintenance, visit The American Basketball Council website at IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. WARRANTY CARD: Please remember to complete your product registration form either on-line at: or mail-in the enclosed postcard. 4 P/N 211984A 04/03 Get to know the basic parts of your basketball system..... STRUTS BACKBOARD FRONT RIM WHEEL CARRIAGE ASSEMBLY BASE POLE 5 04/03 P/N 211984A PARTS LIST - (See Hardware Identifier) Item Qty. Part No. Description 1 1 206740 Tank (White) 2 1 200628 11.75 Long Axle Rod 3 2 226401 Wheel 4 1 900220 Top Pole Section (White) 5 1 201190 Cap (White) 6 1 986102 Bottom Pole Section (White) 7 1 202822 Eyebolt, 3/8-16 x 3-3/4 Long 8 1 202820 Rod, 3/8 O.D. x 4-3/4 Long 9 1 200627 Bracket Wheel Carriage 10 1 203063 Lock Nut, Nylon Insert, 3/8-16 11 1 201625 Bolt, Hex Head, Yellow Dichromate, 5/16-18 x 3.60" Long 12 6 203218 Washer, 5/16 Flat 13 2 986206 Tank Strut (White) 14 1 203220 Lock Nut, 5/16-18 15 1 200439 Label, Height Adjustment and Moving 16 2 203156 Bolt, Hex Head, 5/16-18 x 1 Long 17 6 203100 Nut, Hex Flange 5/16-18 18 1 Rim 19 12* 201219 Clip, Net Holder Smart Clip 20 2 900207 Backboard Mounting Bracket 21 4 203309 Washer, 1 O.D. 22 4 203113 Bolt, Hex Flange, 5/16-18 x 2-1/2 Long 23 2 203231 Bolt, Carriage 5/16-18 x 3-1/2 Long 24 2 203435 Knob, Plastic, 1-3/4 Diameter 25 1 Net 26 1 201568 Tie Down Strap 27 1 203124 Tie Down Stake 28 1 201189 Base Plug 29 2 201651 Spacer, Plastic * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. WARRANTY CARD: Please remember to complete your product registration form either on-line at: or mail-in the enclosed postcard. 6 P/N 211984A 04/03 HARDWARE IDENTIFIER (BOLTS & STEEL RODS) Item #16 (2) Item #22 (4) Item #7 (1) Item #11 (1) Item #8 (1) Item #23 (2) HARDWARE IDENTIFIER (NUTS & WASHERS) Item #14 (1) Item #10 (1) Item #17 (6) Item #21 (4) Item #12 (6) HARDWARE IDENTIFIER (PLASTIC CLIPS & SPACERS) Item #19 (12)* Item #29 (2) 7 04/03 P/N 211984A SECTION A: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) 9/16” and 1/2” 9/16” and 1/2” AND/OR Item #14 (1) Item #12 (6) Item #10 (1) Item #16 (2)Item #17 (6) Item #7 (1) Item #11 (1) Item #8 (1) Item #29 (2) 8 P/N 211984A 04/03 1. 1 Remove contents from tank Remove contents from tank 4 TOP 2. Correctly identify each pole section and mark indicated distance from ends with tape as shown. 6 BOTTOM TAPE (Not Supplied) 5” (13 cm) 3. WOOD SCRAP IMPORTANT! Center the alignment slot of bottom pole section (6) in the lower hole of top pole section (4) as shown. While maintaining alignment, bounce ...