Votes - 5, Average rating: 3.8
(
)
)
|
manual abstract
WARRANTY CARD: Please remember to complete your product registration form either on-line at: or mail-in the enclosed postcard. 3 11/03 P/N 211644 Item Qty. Part No. Description 1 1 Rim 2 2 202604 Bolt, Carriage 3/8 x 4.75” Long 3 2 203474 Washer, Flat, 1”O.D. 4 2 203017 Hex Nut, 3/8” 5 2 203063 Nylon Lock-Nut, 3/8” 6 8 203232 Washer, 3/4” O.D. 7 2 200484 Spring, Zinc 8 2 202601 Washer, Flat 9 2 202602 Lock Washer 10 2 202523 Spacer 11 2 203439 Bolt, Hex, 3/8 x 6” Long 12 2 220140 Screw, Self-Tapping 13 1 908087 Back Bracket - Red 14 1 108085 Inner Bracket - Zinc 15 1 918086 Cover Plate - Red 16 4 201611 Bolt, Hex, 5/16-18 x 3" Long 17 4 203100 Whiz Nut, 5/16” 18 1 204290 Net 19 1 202655 Label, Logo 20 2 202636 Special Nut, Locking 21 2 203795 Special Nut 22 2 202603 Nylon Washer 23 1 202531 Tension and Leveling Label PARTS LIST - See Hardware Identifier BACK BRACKET SPRINGS Get to know the basic parts of your basketball system..... BACK BRACKET RIM RIM Item Qty. Part No. Description 1 1 Rim 2 2 202604 Bolt, Carriage 3/8 x 4.75” Long 3 2 203474 Washer, Flat, 1”O.D. 4 2 203017 Hex Nut, 3/8” 5 2 203063 Nylon Lock-Nut, 3/8” 6 8 203232 Washer, 3/4” O.D. 7 2 200484 Spring, Zinc 8 2 202601 Washer, Flat 9 2 202602 Lock Washer 10 2 202523 Spacer 11 2 203439 Bolt, Hex, 3/8 x 6” Long 12 2 220140 Screw, Self-Tapping 13 1 908087 Back Bracket - Red 14 1 108085 Inner Bracket - Zinc 15 1 918086 Cover Plate - Red 16 4 201611 Bolt, Hex, 5/16-18 x 3" Long 17 4 203100 Whiz Nut, 5/16” 18 1 204290 Net 19 1 202655 Label, Logo 20 2 202636 Special Nut, Locking 21 2 203795 Special Nut 22 2 202603 Nylon Washer 23 1 202531 Tension and Leveling Label PARTS LIST - See Hardware Identifier BACK BRACKET SPRINGS Get to know the basic parts of your basketball system..... BACK BRACKET RIM RIM 4 P/N 211644 11/03 5 11/03 P/N 211644 HARDWARE IDENTIFIER (NUTS & WASHERS) HARDWARE IDENTIFIER (METAL SPACERS & NYLON WASHERS) Item #3 (2) Item #4 (2) Item #5 (2) Item #6 (8) Item #8 (2) Item #10 (2) Item #11 (2) Item #12 (2) Item #16 (4) Item #17 (4) Item #9 (2) Item #21 (2) Item #20 (2) Item #22 (2) HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #2 (2) P/N 211644 11/03 6 1 3 2 9 4 Install two carriage bolts (2) through rim (1), washers (3), and lock washers (9) as shown. Tighten nuts (4) completely. 1. Place a special locking nut (20) approximately half-way up on each carriage bolt (2) as shown. Keep the two special locking nuts (20) at the same level. 2. Perform this step twice as it is applied to both holes of rim bracket shown NOTE: NOTE: COMPLETED ASSEMBLY: 2 NOTE: COMPLETED ASSEMBLY: 20 3a. 1 13 20 Then, insert spacer (10) through back bracket (13), nylon washers (22) and rim assembly (1). Ends of spacer (10) should be flush on both sides of board bracket (13). NOTE: BOTTOM VIEW 13 10 Spacer flush with bracket BOTTOM VIEW 13 22 22 10 1 Line up holes 22 22 Spacer flush with bracket 13 10 First, test fit spacer (10) into back bracket (13) and Carefully rock in a circular motion to ream out any excess paint from holes if necessary. Place rim (1) into back bracket (13) so that the holes are properly aligned. 3b. 3c. 3a. 1 13 20 Then, insert spacer (10) through back bracket (13), nylon washers (22) and rim assembly (1). Ends of spacer (10) should be flush on both sides of board bracket (13). NOTE: BOTTOM VIEW 13 10 Spacer flush with bracket BOTTOM VIEW 13 22 22 10 1 Line up holes 22 22 Spacer flush with bracket 13 10 First, test fit spacer (10) into back bracket (13) and Carefully rock in a circular motion to ream out any excess paint from holes if necessary. Place rim (1) into back bracket (13) so that the holes are properly aligned. 3b. 3c. 7 11/03 P/N 211644 4. Install bolt (11) through top holes on bracket (13) using washers (6) and nut (5) as shown. Tighten completely. 11 6 6 10 5 22 22 Attach rim assembly to backboard and support structure by inserting bolts (16) through bottom holes in back bracket (13). Secure with nuts (17) and washers (6). Tighten nuts (17) completely. 13 5. 17 6 16 16 617 4. Install bolt (11) through top holes on bracket (13) using washers (6) and nut (5) as shown. Tighten completely. 11 6 6 10 5 22 22 Attach rim assembly to backboard and support structure by inserting bolts (16) through bottom holes in back bracket (13). Secure with nuts (17) and washers (6). Tighten nuts (17) completely. 13 5. 17 6 16 16 617 8 P/N 211644 11/03 9 11/03 P/N 211644 Position rim assembly (1) 90 degrees to back bracket (13) as shown. Place inner-bracket (14) over both carriage bolts (2) followed by springs (7), washers (8) and special nuts (21). NOTE: COMPLETED ASSEMBLY: 6. Tighten special nuts (21) until flush with end of carriage bolts (2) as shown. NOTE: 14 7 8 2 21 1 13 Do not over tighten as rim will not flex properly. See leveling instructions (Step 11) to determine how much to tighten nuts (20) and (21). NOTE: Lower lower rim down. Holes in inner bracket (14) should line up with holes in backboard bracket (13). If not, adj...