Votes - 1, Average rating: 5
(
)
)
|
manual abstract
Use a Phillips screwdriver to loosen the screw from the battery compartment, and remove the cover. 2. Placea 9V battery (not supplied) in the compartment as indicated by the polarity symbols (+ and – ). 3. Replace the cover and secure it with the screw. Replacing Batteries in the Bug 1. Turn off the Bug. 2. Use a Phillips screwdriver to loosen the screw from the battery compartment, and remove the cover. 3. Remove the old batteries and place three new AA batteries in the compartment as indicated by the polarity symbols (+ and – ). 4. Replace the cover and secure it with the screw. Driving the Honey Bee I Bug ON/OFF is set to ON when shipping. Slide it once to OFF and then to ON. Use the transmitter's control buttons to drive and steer the Bug. • Press Zto move forward. • Hold down Uto spin clockwise. • Hold down Uto spin counterclockwise. When youfinishdriving theBug,turnitoff. Step One Step Two • Bug • Three AA Batteries • Dispose of old batteries promptly and properly. • Do not burn or bury batteries. • Use only fresh batteries of the required size and recommended type. • Do not mix old and new batteries, different types of batteries or rechargeable batteries of different capacities. • If you do not plan to use the bug for several days, remove the batteries. Batteries can leak chemicals that can damage electronic parts. • Batteries purchased for use in this toy may pose a hazard to children. Please check safety notice supplied with batteries before use. Notes • If you do not play with the Bug for about five minutes while it is turned on, it goes into sleep mode. To restart the Bug, slide ON/OFF on the Bug to OFF, then ON,orpress Try me on. • When the Bug goes outside the transmitter’s range, it stops. Hold the transmitter as high as possible (with the antenna vertical) to try to re-establish contact. Continue to move closer to the Bug until you can control it with the transmitter. Battery Notes • Transmitter RC Honey Bee I Bug 60-2792 What’s Included Step Three Installing Batteries In the Transmitter 1. Use a Phillips screwdriver to loosen the screw from the battery compartment, and remove the cover. 2. Placea 9V battery (not supplied) in the compartment as indicated by the polarity symbols (+ and – ). 3. Replace the cover and secure it with the screw. Replacing Batteries in the Bug 1. Turn off the Bug. 2. Use a Phillips screwdriver to loosen the screw from the battery compartment, and remove the cover. 3. Remove the old batteries and place three new AA batteries in the compartment as indicated by the polarity symbols (+ and – ). 4. Replace the cover and secure it with the screw. Driving the Honey Bee I Bug ON/OFF is set to ON when shipping. Slide it once to OFF and then to ON. Use the transmitter's control buttons to drive and steer the Bug. • Press Zto move forward. • Hold down Uto spin clockwise. • Hold down Uto spin counterclockwise. When youfinishdriving theBug,turnitoff. Step One Step Two • Bug • Three AA Batteries • Dispose of old batteries promptly and properly. • Do not burn or bury batteries. • Use only fresh batteries of the required size and recommended type. • Do not mix old and new batteries, different types of batteries or rechargeable batteries of different capacities. • If you do not plan to use the bug for several days, remove the batteries. Batteries can leak chemicals that can damage electronic parts. • Batteries purchased for use in this toy may pose a hazard to children. Please check safety notice supplied with batteries before use. Notes • If you do not play with the Bug for about five minutes while it is turned on, it goes into sleep mode. To restart the Bug, slide ON/OFF on the Bug to OFF, then ON,orpress Try me on. • When the Bug goes outside the transmitter’s range, it stops. Hold the transmitter as high as possible (with the antenna vertical) to try to re-establish contact. Continue to move closer to the Bug until you can control it with the transmitter. Battery Notes • Transmitter • Your bug works best on firm surface ( but not slippery) such as a wooden or tile floor. • Running your bug continuously for long periods of time generates high heat levels. Heat causes wear and tear on motor. To keep heat level down, cool your bug at least 10 minutes before installing fresh batteries. • If the bug's antennae flashes but does not respond to the transmitter, move closer to the bug and try again. • If someone uses a CB nearby, it might interfere with control of the bug. If this happens, move the bug away from the CB. • You cannot operate your bug near devices with transmitters that use the same frequency as your bug ( 27 or 49 MHz) . Check the box to see which frequency you have. • If the bug moves slowly and you have installed fresh batteries, check the wheel mechanisms for lint, thread, hair or dust. Helpful Hints • Your bug works best on firm surface ( but not slippery) such as a wooden or tile floor. • Running your bug continuously for long periods of time generates high heat leve...