6901-002026 <02> 6901-002026 <02> 7 M8 x 40mm M4 x 30mm M6 x 35mm M5 x 30mm M4 / M5 M6 / M8 M4 / M5 M6 / M8 1/4 x 2.0 in. 1/4 in. 1/4-20 #10 x 1 in. 1/4-20 [08] x 2 [09] x 2 [10] x 2 [11] x 2 [12] x 2 [13] x 2 [14] x 2 [15] x 2 [04] x 2 [05] x 1 [06] x 1 [07] x 1 [01] x 1 [02] x 1 [03] x 2 8 6901-002026 <02> 1 CAUTION: Attach TV Supports (T) to TV 1. Hand thread screws into the threaded inserts on the back of your TV to determine the correct screw diameter (M4, M5, M6, or M8). 2. Attach TV supports (T) using one of the M4, M5, M6, or M8 screw, washer, spacer combinations shown. CAUTION: Avoid potential personal injuries and property damage! .. TV supports (T) must be attached to the to bottom most mounting holes on the back of your TV. .. Do not use screws without spacers. Standard confi gurations are shown. For special applications, or if you are uncertain about your hardware selection, contact Customer Service. M4 M6 M5 M8 (T) [14] [14] [15] [15] [12] [12] [13] [13] [08] [09] [10] [11] [01] [01] [01] [01] [01] (T) 1 2 Attach the Mounting Plate (P) to Furniture • If you are attaching the anti-tip strap to compatible furniture, see step 2-1. • If you are attaching the anti-tip strap to wood furniture that is at least 26 mm (1 in.) thick, see step 2-2. • If you are attaching the anti-tip strap to metal furniture that is at least 3 mm (1/8 in.) thick, see step 2-3. 6901-002026 <02> 10 6901-002026 <02> 1 2 (P) (S) (S) (S) (S) (P) [05] 2-1 If you are attaching the anti-tip strap to compatible furniture: 1. Place the mounting plate (P) over the threaded insert on the back of the furniture. 2. Insert and tighten screw [05]. CAUTION: To avoid potential injuries or property damage! .. Ensure mounting plate (P) is securely fastened to the furniture. .. Ensure all straps (S) are tight. CAUTION: 6901-002026 <02> 11 2-2 If you are attaching the anti-tip strap to wood furniture: 1. Locate a secure area near the top of the furniture that is at least 26 mm (1 in.) thick. 2. Drill pilot hole to a depth of 26 mm (1 in.) using a 2.4 mm (3/32 in.) diameter drill bit. 3. Place the mounting plate (P) over the drilled hole on the back of the furniture. Insert and tighten screw [06]. CAUTION: To avoid potential injuries or property damage! .. Ensure mounting plate (P) is securely fastened to the furniture. .. Ensure all straps (S) are tight. CAUTION: 1 2 3 (S) (P) [06] (P) (S) (S) 2.4 mm (3/32 in.) 12 6901-002026 <02> 2-3 1 2 3 (S) (P) [07] (P) (S) (S) If you are attaching the anti-tip strap to metal furniture: 1. Locate a secure area near the top of the furniture that is at least 3 mm (1/8 in.) thick. 2. Drill pilot hole to a depth of 13 mm (1/2 in.) using a 6 mm (15/64 in.) diameter drill bit. 3. Place the mounting plate (P) over the drilled hole on the back of the furniture. Insert and tighten screw [07]. CAUTION: To avoid potential injuries or property damage! .. Ensure mounting plate (P) is securely fastened to the furniture. .. Ensure all straps (S) are tight. CAUTION: 6 mm (15/64 in.) 3 mm (1/8 in.) 12 mm (7/16 in.) 3 mm (1/8 in.) 12 mm (7/16 in.) CAUTION: Attach Wall Plate [02] and Anti-tip Strap [01] to Wood Stud Wall 1. Locate stud. Verify the center of the stud with an awl or thin nail or use an edge to edge stud fi nder. 2. Level the wall plate [02] and mark the hole locations. 3. Drill pilot holes as illustrated. 4. Tighten the lag bolts [03] only until the washers [04] are pulled firmly against the wall plate [02]. 5. Insert the strap hook (H) into the wall plate [02]. 6. Rotate the strap hook (H) so that it is perpendicuar to the wall plate [02]. 7. Tighten straps (S). NOTE: If you need to move your funiture, loosen the straps and then unclip the strap hook (H) from the wall plate [02]. CAUTION: Improper use could reduce the holding power of the lag bolt. To avoid potential injuries or property damage: • Pilot holes must be drilled to a depth of 63.5 mm (2.5 in.), using a 3mm (1/8 in.) diameter drill bit. • Do not over-tighten the lag bolts [03]. • Any material covering the wall must not exceed 16 mm (5/8 in.). [02] [01] 6901-002026 <02> 14 6901-002026 <02> 3 4 [02] < 16 mm (5/8 in.) [04] [03] 3 1 2 [02] 63.5mm 2.5 in. 5 6 7 [02] [02] (H) (H) (H) (S) [02] 5 6 7 [02] [02] (H) (H) (H) (S) [02] 6901-002026 <02> Francais ATTENTION: INFORMATIONS IMPORTANTES CONCERNANT LA SECURITE – CONSERVEZ CES INSTRUCTIONS – VEUILLEZ LIRE ATTENTIVEMENT LE MANUEL AVANT D’UTILISER CE PRODUIT Merci d’avoir achete la courroie antibasculement ELM701. Ce produit s’installe en 3 etapes faciles ! 1. Fixation de la courroie au televiseur. 2. Fixation au meuble. 3. Optionnel – Fixation au mur. Voir le manuel pour des instructions detaillees. ATTENTION: Evitez les dommages materiels et les blessures! • Ne pas utiliser ce produit a d’autres fins que celles specifiees par fabricant. • Ce produit est concu seulement pour etre installe sur un mur dont la charpente est en bois! • Si vous ne comprenez pas toutes ces instructions ou si vous avez des do...