Votes - 2, Average rating: 4.5
(
)
)
|
manual abstract
No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Symbol products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Symbol products. Symbol and the Symbol logo are registered trademarks of Symbol Technologies, Inc. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. Symbol Technologies, Inc. One Symbol Plaza Holtsville, N.Y. 11742-1300 Warranty For the complete Symbol hardware product warranty statement, go to: Patents This product is covered by one or more patents. For patent information go to: Quick Reference Guide Quick Reference Guide The PhaserLink 360/460 cradle acts as a stand, host communication interface, and charger for the Phaser scanner. For convenience, the cradle can sit on a desktop or be mounted on a wall. The cradle receives data from the scanner via connectors in the bottom of the scanner and the top of the cradle. It then transmits that data to the host device through an attached cable. The cradle also provides power for charging the scanner battery pack (in the scanner). The cradle has a charge status indicator light. Two versions of the cradle are available: -PL 460 cradle: the batch retail version. -PL 360 cradle: the batch industrial version. This Quick Reference Guide provides basic instruction on the set up and use of the cradle. Unless otherwise noted, the term PhaserLink refers to all versions of the cradle. Equipment Supplied The following equipment is supplied: -Two screws (for wall mounting). -One Velcro strip (for desk mounting). -Four rubber feet (for desk mounting). -This Quick Reference Guide. -PhaserLink cradle. Save the shipping container for storing or shipping. Inspect all equipment for damage. If anything is damaged or missing, call your authorized Customer Support Representative immediately. Related Documentation -Phaser Series Scanner Product Reference Guide, p/n 70-33629-xx. -P360/460 Memory Scanners Quick Reference Guide, p/n 70-33628-xx. PL360/460 Cradle PL360/460 Cradle Scanner Support Tab Charging/Communication Contacts Charging LED Indicator COM 1 COM 2 Power Port Wall-mounting Socket 1 Wall-mounting Socket 2 Quick Reference Guide Quick Reference Guide There are three ports on the bottom of the cradle. Power Port COM 1 COM 2 COM 1 connects to the host computer; COM 2 is used for daisy-chaining multiple cradles together; and, the Power Port supplies power to the cradle. Daisy-Chaining 1. Insert the independent power plug into the Power Port. (The cradle cannot be powered by the host computer.) 2. Insert the cable from the host computer into COM 1. 3. Insert the cable to the other cradles, if any, into COM 2. NOTE The cradle supports daisy-chaining when connected to a serial host and not when using Synapse interfaces. To daisy-chain two or more cradles together, connect COM 1 of the first cradle to the host and COM 2 to COM 1 of the second cradle. Then connect COM 2 of the second cradle to COM 1 of the third cradle. Up to 12 cradles can be daisy-chained to one host. PL360/460 Cradle PL360/460 Cradle Before wall-mounting the cradle, the scanner support tab must be changed from the desk-mount position to the wall-mount position. 1 Desk Mount Wall Mount 2 3 1. Lift the scanner support tab out of the top part of the cradle and replace it in the wall-mount position as shown. 2. Seat the cables from the bottom of the cradle in the grooves along the length of the cradle so that the bottom of the cradle is smooth and flat. 3. Secure two screws (included) to the wall. A template is provided on page 14. -Fasten the screws into the wall where the cradle should hang leaving about 1/8” (.3 cm) of the screw outside the wall for the cradle wall moung sockets. 4. Place the cradle over the screw heads and slide down until it fits into place. Slight pressure upwards should not move the cradle. 5. Place the Phaser scanner in the cradle. Quick Reference Guide Quick Reference Guide Place the Phaser scanner in the cradle so that the top of the scanner sits in the larger part of the cradle and the metal contacts on the bottom of the scanner touch the contacts on the cradle. Sending Data to the Host Computer To set up the PhaserLink cradle for communication between a Phaser scanner and a host computer: 1. Connect the cradle to the host computer as described in Connecting to the Host on page 5. 2. Insert the Phaser scanner in the cradle. 3. Start the communication program on the host computer and the Phaser scanner. Recharging the Battery in the Phaser 4. Connect the cradle to a receptacle supplying AC power of the proper voltage level. 5. Place the scanner in the cradle, ensuring the metal co...
Other models in this manual:Baby Furniture - PL460 (629.93 kb)