Votes - 2, Average rating: 4.5
(
)
)
|
manual abstract
b) and place rear-facing on vehicle seat equipped with LATCH anchors. 3 For ease of installation, extend LATCH belt to its maximum length. 4 Hook connectors to vehicle lower anchors (fig. a). Pull connectors to be sure they are securely attached to the anchor points. (fig. b). 5 Press down firmly in center of car seat while pulling LATCH adjustment belt. (fig. c). 6 Pull front to back and left to right to check for secure installation (fig. d). Check that the lower anchorage belt stays tight and does not slip from the tightened position. If it does not stay tight, try another seating position or contact Customer Service (see back cover). 7 Check level indicator on car seat. Vehicle must be on level ground and child in car seat when checking level indicator. Ball MUST be entirely in green zone (fig. e). If necessary, place rolled towels under car seat, at vehicle seat crease, until entire ball is in green zone. Then re-check level indicator. DO NOT use tether rear-facing. Tether must be stored (see “Tether Storage” page 32). Periodically check that car seat is securely installed and properly leveled; adjust if necessary. (fig. b) (fig. c) Openings Towels 9 REAR-FACING INSTALLATION WITH LATCH (continued): (fig. a) (fig. e) (fig. d) Tether LATCH FORWARD-FACING INSTALLATION WITH LATCH 6 1 LATCH belt must be routed through opening in car seat for forward-facing (see page 23, fig. k). Belt must lay flat and not be twisted. 2 Adjust car seat to upright position (see pages 18 and 19, fig. b) and place forward-facing on vehicle seat equipped with LATCH anchors. 3 For ease of installation, extend LATCH belt to its maximum length. 4 Hook connectors to vehicle lower anchors (fig. a). Pull connectors to be sure they are securely attached (fig. b). 5 Press down firmly in center of car seat to compress vehicle seat cushion while tightening LATCH belt by pulling adjustment belt (fig. c). Use your knee to press down in center of car seat (fig. c). Pull front to back and left to right to check for secure installation (fig. d). Check that the lower anchorage belt stays tight and does not slip from the tightened position. If it does not stay tight, try another seating position or contact Customer Service (see back cover). Attach tether strap hook (A) to anchor hardware (B) and tighten adjustment belt to remove any slack (fig. e). Periodically check that car seat is securely installed; adjust if necessary. 7 FORWARD-FACING INSTALLATION WITH LATCH (cont.): Openings (fig. a) (fig. e) (B) (A) Pull to tighten Tether LATCH (fig. b) (fig. c) (fig. d) REAR-FACING INSTALLATION WITH VEHICLE SEAT BELTS WARNING 1 2 3 4 LATCH (see page 23, fig. k). • Attach connectors to storage bar on each side (fig. a). • Adjust LATCH belt to remove excess slack by pulling adjustment belt. Adjust car seat to recline position (see page 18 and 19, fig. b) and place rear-facing on vehicle seat. Thread vehicle seat belt through openings and buckle belt. Press down firmly in center of car seat to compress vehicle seat cushion while tightening vehicle seat belt (fig. b). 5 Pull front to back and left to right to check for secure installation (fig. c). Vehicle lap belt MUST stay tight. If not secure, see “Vehicle Seat Belts” page 26. 6 Check level indicator on car seat. Vehicle must be on level ground and child in car seat when checking level indicator. Ball MUST be entirely in green zone (fig. d). If necessary, place rolled towels under car seat, at vehicle seat crease, until entire ball is in green zone. Then re-check level indicator. DO NOT use tether rear-facing. Tether must be stored (see “Tether Storage” page 32). Periodically check that car seat is securely installed and properly leveled; adjust if necessary. REAR-FACING INSTALLATION WITH VEHICLE SEAT BELTS (continued): (fig. a) Openings Towels 13 (fig. d) (fig. b) (fig. c) Storage Bar Tether LATCH FORWARD-FACING INSTALLATION WITH VEHICLE SEAT BELTS LATCH belt MUST be stored when using vehicle seat belt to install car seat. WARNING 1 2 3 Store LATCH belt by attaching to connectors through rear-facing openings (see page 23, fig. j). • Attach connectors to storage bar on each side (fig. a). • Adjust LATCH belt to remove excess slack by pulling adjustment belt. Adjust car seat to upright position (see pages 18 and 19, fig. b) and place forward-facing on vehicle seat. Lift seat pad flap (available on some models). Thread vehicle seat belt through openings. Buckle belt (fig. b). 4 5 6 Press down firmly in center of car seat to compress vehicle seat cushion while tightening vehicle seat belt. Use your knee to press down in center of car seat (fig. c). Pull front to back and left to right to check for secure installation (fig. d). Vehicle lap belt MUST stay tight. If not secure, see “Vehicle Seat Belts” page 26. Attach tether strap hook (A) to anchor hardware (B) and tighten adjustment belt to remove any slack (fig. e). If vehicle does not have anchor points to attach tether hook, tether hook should be stored, ...