Votes - 3, Average rating: 4.7
(
)
)
|
manual abstract
WARNING Safety Guidelines to Prevent Injury • NOT INTENDED FOR CARRYING BABY. • NEVER leave child unattended in the bouncer. • ALWAYS use restraint system. • NEVER use for a child who is able to sit upright unassisted. • NEVER place a child over 25 lbs. (11 kg) in the bouncer. • NEVER lift bouncer using the toy bar as a handle. • NEVER move unit while child is in seat! • NOT for use in automobile or airline travel. • NEVER use as a car seat or infant carrier. • NEVER attach any additional strings or straps to product or toy bar. FALL HAZARD: • A child’s movement can slide the bouncer. • NEVER place the bouncer on countertops, tables, on or near steps or on other elevated surfaces. • ALWAYS use on the floor. ESPANOL: PAGINA 7 • FRANCAISE : PAGE 13 IMPORTANT! KEEP FOR FUTURE REFERENCE. SUFFOCATION HAZARD: • NEVER use on a soft surface (bed, sofa, cushion), as seat may tip over and cause suffocation. IMPORTANT: • Adult assembly required. • Care should be taken when unpacking the bouncer. • Examine product frequently for damaged, missing, or loose parts. • Do not use product if damaged or broken. Assembly Instructions Connect the wire uprights to the base frame wire. A Place the base frame wire on a flat surface. The two rear anti-skid feet must be facing down, contacting the surface. Base frame wire 1 Holes on top Right wire Anti-skid feet Left wire upright upright B Locate the left and right wire uprights and place them near the corresponding ends of the base frame wire. If the parts are correctly placed, the holes in the sockets will be on top. C Push the socket on the end of the left wire upright onto the left end of the base frame wire. The hole in the side of the socket must face inward toward the opposite end of the base frame wire. Hole in side of socket D Press the spring-loaded button and push the socket until the spring-loaded button fully engages, locking the frame wires together. E Repeat Steps C and D for the right wire upright. – 1 – The base frame assembly is complete. Set it aside for use in a later step. Assemble the seat frame. A Locate the footrest wire frame with connecting hubs. Place it on a flat surface with the toy bar sockets pointing upward as shown. Sockets pointing upward Footrest wire frame Backrest wire frame Connecting hub Connecting hub B Locate the backrest wire. Position it so that the wire ends are near the connecting hubs. C Partially insert both left and right ends of the backrest wire into the corresponding sockets in the connecting hubs. (Stop just before either spring-loaded button enters the hub.) NOTE: To avoid binding, do not fully insert one wire end before inserting the other end. D Press the spring- loaded button on the left end of the backrest wire and fully insert it into the connecting hub. Verify that the button fully engages, latching the wire frame to the hub. E Repeat Step D for the right end of the backrest wire. Connect the seat frame to the base frame. A Hold the seat frame in 3 Sockets pointing position above the base frame. Prepare for assembly by verifying that: • the toy bar sockets on the connecting hub point upward, and... • the wire ends on the base frame point toward the corresponding holes in the connecting hubs. B Partially insert both left and right ends of the base frame wire into the holes in the connecting hubs. (Stop just before either spring- loaded button enters the hub.) C Press the spring-loaded button on the left end of the backrest wire and fully insert the wire into the connecting hub. Verify that the button fully engages, locking the wire frame into the hub. D Repeat Step C for the right end of the base frame wire. E Inspect both connecting hubs to verify that the frame wires are fully inserted. Be sure that the two spring-loaded buttons at each hub have fully engaged. The bouncer frame assembly is complete. Attach the seat pad to the seat frame. 4 CAUTION: Adjust the wiring as needed to keep it away from the U-shaped recess in the frame. Otherwise, the vibration unit may crimp the wiring. Correct Incorrect upward Connecting hub Spring-loaded buttons – 2 – A Locate the seat pad and Straps with buckles place it upside down on a firm surface. B Unbuckle the straps on each side of the seat pad. C Unfasten the hook-andloop strap and fold back the two fabric flaps. Hook-and-loop strap Fabric flaps D Hold the seat pad above the seat frame. Turn the seat pad so that opening for the vibration unit is at the front of the frame (footrest). E Open the pocket at the top edge of the seat pad and slide it over the backrest frame. F Lift up the two fabric flaps (shown below). Slide the two flaps over and under the footrest wire. Fabric flaps lifted G Gently tilt the bouncer backward until the backrest contacts the floor. H Fasten (buckle) the straps together on each side, securing the seat pad to the frame. NOTE: Do not fasten the hoop-and-loop patches yet. That step will occur after the vibration unit installation. Fabric pocket in seat pad Openi...