Votes - 0, Average rating: 0 ( )

Manafacture: Philips File size: 96.88 kb File name: Language of manual:

2 ) 9 ALARM 1 indicator - lights up when alarm 1 is activated. 0 ALARM 2 indicator - lights up when alarm 2 is activated. ! DISPLAY - shows the clock/alarm time and status of the setting @ Frequency pointer - shows the radio frequency of your selected waveband Back View (see fig. 3 ) # Battery door - opens to store a 9 volts 6F22 battery (not included) for clock memory backup. $ TUNING - tunes to radio stations % FM/MW -selects FM/MW waveband ^ BRIGHTNESS (High or Low) -selects display brightness & Power cord -connects to wall outlet * Pigtail - improve FM reception ( VOLUME - adjusts the sound level INSTALLATION POWER SUPPLY 1 Check if the power supply, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service center. 2 Connect the power cord to the wall outlet. 3 To disconnect the set from the power supply completely, remove the plug from the wall outlet. SELECTING DISPLAY BRIGHTNESS This set allows you to choose high or low brightness of display. • Adjust BRIGHTNESS switch (located on the rear of the set) to HIGH or LOW position. CLOCK MEMORY BACKUP The clock memory backup allows your alarm and clock time settings to be stored for up to a day when there is a power interruption e.g. power failure. The complete clock radio and display illumination will be switched off. As soon as the power supply returns, the display will indicate the correct time. 1 Remove the battery door to insert a 9 volts 6F22 type battery (not included) for backup. 2 Replace the battery door. NOTE: If no backup battery is installed or the power interruption is prolonged, you will need to set the clock and alarm times again. Batteries contain chemical substances so they should be disposed of properly. Standby power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .< 2W RADIO You can use this set solely as a radio! 1 Adjust OFF/ ON/ AUTO/ BUZZ to ON to switch on the radio. 2 Select your waveband by adjusting the FM/MW switch. 3 Adjust TUNING to tune to your desired station. 4 Turn the VOLUME control to adjust the volume level. 5 Adjust OFF/ ON/ AUTO/ BUZZ to OFF to switch off the radio. To improve reception: FM: Extend and position the pigtail fully to obtain optimal reception. MW: uses a built-in antenna inside the set. Direct the antenna by adjusting the position of your set. SETTING THE CLOCK TIME The time is displayed using the 24-hour clock. 1 Hold down SET TIME/ALARM OFF. 2 Press TIME SET 3 or 4 repeatedly, or hold down TIME SET 3 or 4 to adjust minute and/or hour. -TIME SET 3 : to adjust time fast forward -TIME SET 4 : to adjsut time back 3 Release SET TIME/ALARM OFF and TIME SET 3 or 4 when you reach the correct setting. ™ The set clock time will show on the display and start to run. USING THE ALARM This set allows you to set one alarm (alarm 1 or alarm 2), or set two alarms simultaneously. This set also offers you two alarm modes: Auto (radio) and Buzz. SETTING THE ALARM TIME 1 Hold down SET ALARM 1 or SET ALARM 2 2 Press TIME SET 3 or 4 repeatedly, or hold down TIME SET 3 or 4 to adjust minute and/or hour. 3 Release SET ALARM 1 or SET ALARM 2, and TIME SET 3 or 4 when you reach the desired time setting. The display will return to the clock time. SELECTING THE ALARM MODE 1 Adjust AL1/AL2/AL1+2 to AL1 (alarm 1), or AL2 (alarm 2), or AL1+2 (alarm 1 + alarm 2) . 2 Select your choice of alarm mode by adjusting OFF/ ON/ AUTO/ BUZZ to AUTO or BUZZ. ™ The corresponding alarm indicator(s) will light up. Helpful Hint: • If you have selected the radio mode, make sure you have adjusted the volume loud enough to wake you. • The buzzer is set at a fixed volume and cannot be adjusted. SWITCHING OFF THE ALARM There are three ways of switching off the alarm. Unless you cancel the alarm completely, the 24 hour alarm reset option will be automatically selected after 59 minutes, from the time your alarm time first goes off. 24 HOUR ALARM RESET If you want the alarm mode to be stopped immediately but also wish to retain the same alarm setting for the following day: • Press SET TIME/ALARM OFF during the alarm call. CANCELING THE ALARM COMPLETELY To cancel the set alarm time before it goes off, or during the alarm call: • Adjust OFF/ON/AUTO/BUZZ to OFF position. REPEAT ALARM This repeats your alarm call at 7-8-minute intervals. 1 During the alarm call, press REPEAT ALARM. 2 Repeat if desired for up to 59 minutes. SLEEP This set has a built-in timer which enables the set to be automatically switched off during radio playback after a set period of time. This allows you to lie back, listen and fall asleep. The maximum sleep time is 59 minutes. Setting SLEEP 1 Set OFF/ON/AUTO/BUZZ to OFF position. 2 Set your sleep time by pressing on the SLEEP button. Keep your finger on the button and the display will begin to count down from 0:59 to 0:00 minute. ™ To cancel sleep, press SET TIME/ALARM OFF. ™ To view the remaining sleep time, pres...

Download now

Please, enter two numbers from picture: