Votes - 0, Average rating: 5 ( )

Manafacture: Accusplit File size: 637.48 kb File name: Language of manual:

Press and Hold to Reset. #998-310A In the classroom, the Time Timer can be used to set time limits, measure the duration of activities and train students to make better use of available time. Use the Time Timer products to: • Time standardized tests • Monitor math and writing speed tests • Measure study periods and lunch periods • Regulate computer time • Administer duration drills • Show time left to play, get ready or clean up Using Time of Day and Alarm Press MODE (lower left) button until the watch shows the Time, displayed both in traditional “analog” form, and also in digital format in center. Notice that the Hour hand is continuously lit, while the minute hand flashes slowly. There is also a second hand sweeping around. Press TIMER (upper right) button to see the Time of Day alarm setting. The watch returns to current time after a few seconds. Or, press MODE twice to see current time immediately. When the Time of Day alarm sounds, press any button to silence it. To change the settings for Time of Day or Time of Day Alarm, see the instructions below. Setting the Watch The watch uses a standard setting procedure to set all modes. It works as follows: • Press and hold “S1” to enter setting mode • Press “S2” to change the field to set • Press “S3” to change the value of the field being set • Press “S4” to exit setting mode Setting the Timer The timer must be stopped before changing settings. To set the timer, first press the MODE button until you see the Time Timer’s red dial display appear. Press and hold the S1 button (upper left) for about three seconds, until the numbers in the middle begin to flash, indicating that you have entered setting mode. TIME TIMER0 5 10 15 55 20 25 30 35 40 45 50 30MWATER RESIST TIME TIMER0 5 10 15 55 20 25 30 35 40 45 50 30MWATER RESIST AMHour hand Minute hand flashing TIME TIMER0 5 10 15 55 20 25 30 35 40 45 50 30MWATER RESIST TIME TIMER0 5 10 15 55 20 25 30 35 40 45 50 30MWATER RESIST .. Pre-alarm is ON Alarm is ON S1 & S4 S3– S3+ S2 TIME TIMER0 5 10 15 55 20 25 30 35 40 45 50 30MWATER RESIST TIME TIMER0 5 10 15 55 20 25 30 35 40 45 50 30MWATER RESIST AMHour hand Minute hand flashing TIME TIMER0 5 10 15 55 20 25 30 35 40 45 50 30MWATER RESIST TIME TIMER0 5 10 15 55 20 25 30 35 40 45 50 30MWATER RESIST .. Pre-alarm is ON Alarm is ON S1 & S4 S3– S3+ S2 Press S2 (upper right) to cycle through the fields you can set. The fields are: Time setting > Alarm On/Off > Pre Alarm On/Off >Time setting (Note that the Pre Alarm can only be set if the Alarm is turned On). Press S2 until you see digits in the center of the display. Now you can set the timer. Press S3+ (lower right) to increase the timer set point, and press S3– (lower left) to decrease the set point. You will see both the digits and also the dial size increase or decrease. Setting Notes: 1. You can either press and release S3+ and S3– to change field values, or “press and hold” either of the S3 buttons to rapidly change the field value. 2. As you pass through each hour while setting, rapid advance stops. This helps avoid overshooting your desired set point. 3. The timer can be set to a minimum of 1 minute and a maximum of 12 hrs. 4. You can return to the default timer setting of 60 minutes by simultaneously pressing S3+ and S3–. Once you have set the desired time, press S2 once to change Alarm On/Off Setting. You will see the word “ON” or “OFF,” plus an alarm •3 symbol, both flashing. Press S3+ or S3– to turn the Alarm on or off. If you have turned the Alarm ON, you can now change the Pre-Alarm settings by pressing S2 again. Again, the Pre-Alarm can only be set if the Alarm is ON. If the Alarm is OFF, pressing S2 will return you to the Time setting field. In Pre-Alarm set, you will see the word “ON” or “OFF,” plus TWO alarm •3 symbols. The Pre-Alarm symbol (smaller and on the left) will be flashing, along with ON or OFF. Press S3+ or...

Download now

Please, enter two numbers from picture: