Votes - 0, Average rating: 0
(
)
)
|
manual abstract
3 To switch to LINE IN mode, connect an external audio source to the LINE-IN inlet. Helpful hints: • The set switches to LINE IN mode automatically when an external audio source is connected, no matter the set is in CD, FM or MW mode. • The LINE-IN inlet is not for earphones. Adjusting volume and sound Adjust the sound with the VOLUME and DBB controls. Tuner MP3-CD/CD Player Radio reception 1 Adjust the Source selector to FM or MW. 2 Turn TUNING to tune to a station. Helpful hints: To improve radio reception • For FM, extend, incline and turn the telescopic antenna for best reception. Reduce its length if the signal is too strong. • For MW, the set uses a built-in antenna. Direct this antenna for best reception by turning the whole set. About MP3 The music compression technology MP3 (MPEG1 Audio Layer 3) significantly reduce the digital data of an audio CD while maintaining CD quality sound. • Getting MP3 files: you can either download legal music files from the internet to your computer hard disc, or create such files by conver ting audio CD files in your computer through appropriate encoder software. (128kbps bit rate or higher is recommended for MP3 files.) • Creating a MP3 CD: burn the music files from your computer hard disc on a CDR or CDRW using your CD burner. Helpful Hints: – Make sure that the file names of the MP3 files end with .mp3 . – Total number of music files and albums: around 400 (with a typical file name length of 20 characters) – The length of file names affects the number of tracks for playback. With shorter file names, more files can be burned on a disc. Playing a disc • This CD player plays Audio Discs including CD-Recordables (CD-R), CD-Rewritables (CD-RW) and MP3 CD. • CD-ROM, CD-I, CDV, VCD, DVD or computer CDs are not possible for playback. IMPORTANT! • CDs encoded with copyright protection technologies by some record companies may be unplayable by this product. 1 Adjust the Source selector to CD. 2 Open the CD door, and inser t a CD with the printed side facing up, then press the CD door gently to close. . Display shows ---, and later the total number of tracks. (See 3) 3 Press 2; to star t playback. 4 To pause playback, press 2;. . Display: 2 flashes. (See 4) 5 To resume, press 2; again. 6 To stop CD playback, press 9. Helpful hints: CD play will also stop when: – you open the CD door ; – you select FM, MW or OFF sound source; – the CD has reached the end. MP3-CD/CD Player Selecting a different track • Press ./ § once or repeatedly until the desired track number appears in the display. For MP3-CD: First press 43 once or more to find your album. • In the pause/stop position, press 2; to start playback. Finding a passage within atrack 1 During playback, press and hold . or § . . The CD is played at high speed and with reduced volume. 2 When you recognize the passage you want, release . or § to resume normal playback. Helpful hints: – When your searching reaches the end of the last track, the CD goes to stop mode. Programming track numbers You may store up to 20 tracks in the desired sequence. If you like, store any track more than once. 1 In the stop position, press PROG to activate programming. . Display: PROG and P01 flash. (See 5) 2 Press . or § to select your desired track number. For MP3-CD: first press 43 once or more to find your album. 3 Press PROG to store the desired track number. . Display: PROG and P02 flash for you to program the next track. 4 Repeat steps 2 to 3 to select and store all desired tracks in this way. . If you attempt to store more than 20 tracks, no track can be selected and the display shows - --- --- --. 5 To play your program, press 2/;. Helpful hints : – When playback of your program comes to the stop position, your set will return to normal playback.To re-enter program mode, press PROG in the stop position. Reviewing the program In the stop position, press PROG repeatedly to see your stored tracks. Erasing a program You can erase the contents of the memory by: – in the stop position, press PROG to enter program mode, and then press 9. – selecting FM, MW or OFF; – opening the CD door; MP3/CD Player Different play modes: REPEAT. and SHUFFLE (See 6, 7) You can select and change the various play modes before or during playback, and combine REPEAT modes with PROG (PROGRAM). – plays the current track continuously. – repeats the entire CD/program. For MP3: ALB –plays all tracks of current album repeatedly. – plays all tracks in random order. 1 To select play mode, press MODE once or more. . The display shows the related icon. 2 Press 2; to star t playback if in the stop/pause position. 3 To return to normal playback, press MODE repeatedly until the modes are no longer displayed. – You can also press 9 to cancel your play mode. Maintenance & Safety (See 8) CD player and CD handling • If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. • The lens of the CD player should never be touched! • Sudden ...