Votes - 0, Average rating: 0
(
)
)
|
manual abstract
Press STANDBY ON y to switch off. Helpful Hints: – The tone, sound settings, tuner presets and the volume level (up to a maximum volume level of VOL 20 ) will be retained in the set's memory. ADJUSTING VOLUME AND SOUND (See 2) • Adjust the volume with the VOLUME control. = Display shows the volume level and a number from 0-32. MAX SOUND To enhance the bass response: press MAX SOUND once or more to switch on / off. = MAX SOUND-key backlight lights up when MAX SOUND is turned on. Helpful Hints: – MAX SOUND can be used when you play FM, MW, CD and GAME AUX source. – Some discs might be recorded in high modulation, which causes a distortion at high volume. If this occurs, deactivate MAX SOUND or reduce the volume. EQUALIZER 1. To adjust the bass, mid and treble frequencies press EQUALIZER once or more; 2. Rotate VOLUME within 3 seconds to adjust each level. = Display briefly shows , or level (-5 to +5) or , . Helpful Hints: – EQUALIZER can be used during FM, MW, CD and GAME AUX source. – To prevent sound interference the bass control options operate exclusively. You cannot combine the bass from EQUALIZER with MAX SOUND. GAMESOUND To adjust the game sound, press GAMESOUND once or more to select your option. = Display briefly shows , , or . Helpful Hints: – GAMESOUND is only available when you play in GAME AUX source. How to MUTE the sound 1. Press MUTE on the remote control to interrupt sound reproduction instantly. = Playback continues without sound and the display flashes . 2. To reactivate sound reproduction you can: – press MUTE again; – adjust the volume controls; – change to another source. DIGITAL TUNER Tuning to stations (See 3) 1. Press STANDBY ON y to on, then press Source selector once or more to select FM/MW (or press FM/MW on the remote control). = Display: shows briefly followed by waveband, frequency, and preset station number if already stored. 2. Tuning to stations: you can tune to your stations manually or by automatic search tuning: Press down on . or § ( 5 or 6 on the remote control) and release button when the frequency in the display starts running. = The radio automatically tunes to a station of sufficient reception. Display shows during automatic tuning. 3. Repeat step 2 if necessary until you find the desired station. •To tune to a weak station, press . or § briefly and repeatedly until you have found optimal reception. Helpful Hints: To improve radio reception: – For FM, extend, incline and turn the telescopic antenna. Reduce its length if the signal is too strong. – For MW, the set uses a built-in antenna. Direct this antenna by turning the whole set. Programming tuner stations: You can store up to a total of 30 radio memory, manually or automatically (Autostore). Autostore Automatic programming will start from preset 1 chosen preset number. The set will only program stations which are not in the memory already. 1. Press ALBUM/PRESET - / + once or more to select the preset number where programming should start. Helpful Hints: – If no tuner preset number is selected, default is preset 1 and all your presets will be erased. 2. Press PROG for 4 seconds or more to activate auto store programming. = Display: is shown and available stations are programmed in order of waveband FM, followed by MW. 3. The first preset station will then be played after all stations are stored automatically. Manual programming 1. Tune to your desired station (see Tuning to stations). 2. Press PROG to activate programming. = Display: program flashes. 3. Press ALBUM/PRESET - / + once or more to allocate a number from 1 to 30 to this stations. 4. Press PROG again to confirm. = Display: shows the preset number, waveband and the frequency of the preset station. This set complies with the radio interference requirements of the European Union. MP3-CD/CD PLAYER About MP3 The music compression technology MP3 Layer 3) reduces the digital data of an audio significantly while maintaining CD-like sound How to get music files Either download legal music files from the internet to your computer hard disc or create them from your own audio CDs. For this, insert an audio CD into your computer.s CD-ROM drive and convert the music using an appropriate encoder software. To achieve a good sound quality, a bit rate of 128 kbps or higher is recommended for MP3 music files. How to make a CD-ROM with MP3 files Use your computer.s CD burner to record (“burn”) the music files from your hard disc on a CD-ROM. Helpful Hints: – For details on using MP3 encoder and writing software, please refer to the operating instructions of the software. – Make sure that the file names of the MP3 files end with .mp3. – Total number of music files and albums: around 350 (with a typical file name length of 20 characters) – The number of music files that can be played depends on the length of the file names. With short file names more files will be supported. IMPORTANT ! This set does not play/support the following file formats: –Word documents .doc or MP3 fi...