Votes - 2, Average rating: 4 ( )

Manafacture: Kenwood File size: 620.98 kb File name: Language of manual:

7 Playback in a random order (Random playback) DPF-3010/2010/1010 (En) As tracks are selected at random, you can enjoy listening to for a long time. The figure shows an example for the DPF-3010 O Load a disc in the CD player. @ Preparation 1 A 4 7 6 . : Keys and control used in the operations described on this page. 1 1 Press the P.MODE key so that the "TRACK" indicator lights. Lights up. TRACK TRACK NO. SINGLE TIME 6 1 7 2 8 3 4 5 9 10 0:1000 In case track No. 5 is selected TRACK SINGLE TIME NO. 05 : 012 TRACK OEach time a track ends, another track is selected and played. ORandom play stops after all of thetracks have been played once. OThe random playback can also be repeated by pressing the REPEAT key. If the "PGM" indicator is lit, press the P.MODE key. 2Press the RANDOM key. P.MODE RANDOM To select another track in the middle of playing one To cancel random playback . RANDOM OPressing the 4 key once returns to the beginning of the track being OPress the RANDOM key to start normal playback. played. Timer operations DPF-3010/2010/1010 (En) This unit Timer playback of CD can be started at any time using an audio timer which is available in audio stores. Preparation OConnect the power cords of the associated components so that their power can be turned ON through the audio timer. (Also, be sure to read carefully the instruction manual of the timer.) 21Audio cordSystem control cord Amplifier Audio timer To wall AC outlet 12F00 1 A 4 7 6 . 1Turn the powers of the associated components ON. 2 2 Preparation Load a disc in the CD player. @ Set the amplifier volume.3Label side 1 A 4 76 . 1 Play the disc. Set the timer ON time.42 Adjust the amplifier volume. (Use the remote control unit of this unit to adjust the volume to the maximum level.) 3 Stop the disc. 6 PLAY/PAUSE 7 STOP Set the timer so that it supplies power at the specified time. O If the amplifier is not connected to the CD player through a system control cord, select the “CD” input with the input selector. NoteNoteNote Adjusting the volume: Set the volume the maximum (0 dB) using the OUTPUT (UP) key on the remote control unit, and adjust the volume to the desired level on the amplifier side. (Since the sound output is at the maximum level when the power is turned on, lowering the level with the remote control will change the volume.) OWith some audio timer models, the power is automatically turned OFF when the timer ON time is set. With such a model, skip step 5 below. 5 5 Turn OFF the power output from the audio timer. ODo not touch the ON/STANDBY switches of the amplifier and CD player. OWhen the set time comes, the disc playback starts automatically. NotesNotes 1. Some amplifiers cannot be used with a timer. Before using a amplifier, check it. 2. When operating the unit other than CD player using an audio timer, be sure to remove the disc from the CD player. In case of difficulty DPF-3010/2010/1010 (En) What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the table below to see if the problem can be corrected before seeking help from your dealer or service representative. 22 Operation to reset The microcomputer may fall into malfunction (impossibil- ity to operate, erroneous display, etc.) when the connec- tion cords are unplugged while unit is ON or due to an external factor. In this case, execute the following method to reset the microcomputer and return it to normal condi- tion. OPlease be aware that resetting the CD player will erase all stored information and return it to the factory settings. Set the unit to STANDBY mode by pressing the ON/ STANDBY ( ) key, and after a few seconds, turn the unit ON by pressing the ON/STANDBY ( ) key again. CD player unit Symptom Cause Remedy The unit is not turned ON with the ON/ STANDBY switch ON. OPower plug is loosely connected. OWith the power plug connected to the switched AC outlet of an amplifier, the power of the amplifier is turned off. OInsert the power plug firmly to the AC outlet. OTurn the amplifier’s power ON. Disc is loaded, player does not play. ODisc is loaded upside down. ODisc is loose. ODisc is dirty. ODisc is cracked. OCondensation has occurred on the optical lens unit. OLoad the disc again with its label side up. OInsert the disc properly. OWipe off the dust on the surface of the disc referring to “Disc handling precautions”. 9 OReplace the disc with a new one. OLeave the player for about 1 hour so that the condensation is removed. 9 No sound. OPlay mode is not entered. ODisc is too dirty. ODisc is cracked. OThe connection cords are inserted loosely. OOutput level is attenuated too low. OPress the 6 key. OWipe off the dust on the disc surface referring to “Disc handling precautions”. 9 OReplace the disc with a new one. OConnect all connection cords firmly. OAdjust the output level with OUTPUT key on the remote control unit. 7 Music is interrupted. (Sound is skipped.) ODisc is too dirty. ODisc is cracked. OOscillation is applied ...

Download now

Please, enter two numbers from picture: