Votes - 1, Average rating: 5
(
)
)
|
manual abstract
1. Press the [RDM ] button. “RDM ” lights in the display, an individual track is selected randomly and play begins. 2. To cancel the random play, press the [RDM ] button again. “RDM ” goes off and normal play resumes. DB168R/BD169R/BD169RG 9 English English 6. SPECIFICATIONS Radio section Tuning System: PLL synthesizer tuner Receiving Frequencies: FM : 87.5 to 108 MHz (0.05 MHz steps) MW : 531 to 1602 kHz (9 kHz steps) LW : 153 to 279 kHz (3 kHz steps) CD player section System: Compact disc digital audio system Frequency Response: 10 Hz to 20 kHz (± 1 dB) Signal to Noise Ratio: 100 dB (1 kHz) IHF-A Dynamic Range: 93 dB (1 kHz) Distortion: 0.03% Note: General Output Power: 4 . 20 W (DIN 45324, +B=14.4V) Power Supply Voltage: 14.4 V DC (10.8 to 15.6 V allowable), negative ground Power Consumption: Less than 15 A Speaker Impedance: 4 . (4 to 8 . allowable) Auto Antenna Rated Current: 500 mA or less Weight: Main unit: 1.125 kg Dimensions: Main unit : 178 (W) . 50 (H) . 155 (D) mm • Specifications and design are subject to change without notice for further improvement. 7. IN CASE OF DIFFICULTY Problem Cause Solution Power does not turn on. (No sound is produced.) Fuse is blown. Replace with a fuse of the same amperage. If the fuse blows again, consult your store of purchase. Incorrect wiring. Consult your store of purchase. Compact disc cannot be loaded. Another compact disc is already loaded. Eject the compact disc before loading the new one. Sound skips or is noisy. Compact disc is dirty. Clean the compact disc with a soft cloth. Compact disc is heaviiy scratched or warped. Replace with a compact disc with no scratches. Sound is bad directly after power is turned on. Water droplets may form on the internal lens when the car is parked in a humid place. Let dry for about 1 hour with the power on. Nothing happens when buttons are pressed. Display is not accurate. Microprocessor has malfunctioned due to noise, etc. Turn off the power, then press the Release button and remove the DCP. Press the reset button for about 2 seconds with a thin rod. Reset button DCP or main unit connectors are dirty. Wipe the dirt off with a soft cloth moistened with cleaning alcohol. 10 DB168R/BD169R/BD169RG 8. ERROR DISPLAYS 8. ERROR DISPLAYS If an error occurs, one of the following displays is displayed. Take the measures described below to eliminate the problem. Error Display Cause Measure ERROR 2 A CD is caught inside the CD deck and is not ejected. This is a failure of CD deck’s mechanism and consult your store of purchase. ERROR 3 A CD cannot be played due to scratches, etc. Replace with a non-scratched, non-warped-disc. If an error display other than the ones described above appears, press the reset button. If the problem persists, turn off the power and consult your store of purchase. English DB168R/BD169R/BD169RG 11 DB168R/BD169R/BD169RG 75 All Rights Reserved. Copyright © 2005: Clarion Co., Ltd. Printed in China / Imprime en Chine / Gedruckt in China / Stampato in Cina 2005/12 Gedrukt in China / Impreso en China / Tryckt i Kina / Impresso na China PE-2797E 280-8304-00 Clarion Co., Ltd. ...
Other models in this manual:CD Players - BD169R (1.73 mb)
CD Players - BD169RG (1.73 mb)