Votes - 2, Average rating: 5
(
)
)
|
manual abstract
1 pc. 4 pcs. 1 pc. Self-tapping screw Seals (A) Seals (B) (M5 x 12) 4 pcs. 1 pc. 1 pc. OTHER ACCESSORIES CD Magazine Index seal sheet Installation Manual Owner’s guide 1pc. 1pc. 1pc. 1pc. BEFORE INSTALLING THE UNIT Transport Lock Screws The mechanism in the CD changer is "locked" into place during shipment by the transport screws. Be sure to remove the screws prior to installation. . Caution . After removing the transport lock screws, place the supplied seals (A) over the screw holes. These seals are used to keep dust out of the unit, which could cause a malfunction. Installation and Wiring Precautions To prevent a short-circuit, 1 . Be sure to turn off the ignition and remove the negative (-) battery cable, prior to installation. . Connect power wires last. Note If the changer is to be installed in a car that is equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution during installation, not to cause a short circuit. Do not install the unit in the following locations. 2 . Locations exposed to direct sunlight. . Where hot air is discharged from the car heater. . In areas subject to extreme temperatures. Incorrect installation can cause the sound to "skip" when playing a disc. 3 Mount the unit firmly in place, using the supplied brackets and screws. 4 Be careful not to damage the car wiring. . Be sure to use the supplied screws. 5 . Be careful not to snag any wires when tightening screws. . Do not use any of the screws that are part of the brake or steering system, to install the unit. . This unit cannot be installed on its side, end, or upside down. Installation in such positions will cause malfunctioning 6 of the mechanism. INSTALLATION The unit can be installed horizontally, vertically or at a 45° angle. The position of the built-in anti-vibration springs (left and right side), must correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, the anti-vibration compensation will not be effective and vibration may cause the disc to skip. CAUTION After setting the built-in anti-vibration springs, place the supplied Seals (B) over the holes. These seals are used to keep dust, which could cause a malfunction, out of the unit. HORIZONTAL INSTALLATION Set the 4 anti-vibration springs to position "H". position "H" VERTICAL INSTALLAITON Set the 4 anti-vibration springs to position "V". position "V" 45° ANGLE INSTALLATION Set the 4 anti-vibration springs to position "45°". position"45°" PROCEDURE FOR HORIZONTAL INSTALLATION Drillholes4mmindiameter. 123Bracket(R) Attachbracket(L)andbracket(R)toeachsideoftheunit, usingthehexagonalboltswithwasherbase(M5x8). Determinethemountinglocation,anddrillfourmountingholes. Securetheunitinplace,usingfourself-tappingscrews(M5x12). UseRTV(siliconesealer)onscrewthreadsoraroundtheholestopreventmoistureintrusion. Self-tappingscrew(M5x12) Nevermounttheunitnearthefueltank. Bracket(L) Bracket(R) Bracket(L) Hexagonalboltwithwasherbase(M5x8) Anti-vibrationspringspositionNOTE:Useseals(A)tocoverunusedmountingholesonsidesofunit. PROCEDURE FOR VERTICAL INSTALLATION Note If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 3), start with step 2. Hexagonalboltwithwasherbase(M5x8) Bracket(R) Bracket(L) 42Attachbracket(L)andbracket(R)toeachsideoftheunit, usingthehexagonalboltswithwasherbase(M5x8). Mounttheunitinplace,usingfourself-tappingscrews(M5x12). UseRTV(siliconesealer)onscrewthreadsoraroundtheholestopreventmoistureintrusion. Setthe4anti-vibrationspringstoposition"V". Determinethemountinglocation,anddrillfourmountingholes. 31Nevermounttheunitnearthefueltank. Drillholes4mmindiameter. position"V" Self-tappingscrew(M5x12) Bracket(R) Bracket(L) NOTE:Useseals(A)tocoverunusedmountingholesonsidesofunit. PROCEDURE FOR 45° ANGLE INSTALLATION Note If the anti-vibration spring position has been changed and verified for 45° angle mounting (as shown on page 3), start with step 2. 42Attachbracket(L)andbracket(R)toeachsideoftheunit, usingthehexagonalboltswithwasherbase(M5x8). Mounttheunitinplace,usingfourself-tappingscrews(M5x12). UseRTV(siliconesealer)onscrewthreadsoraroundtheholestopreventmoistureintrusion. Setthe4anti-vibrationspringstoposition"45°". Determinethemountinglocation,anddrillfourmountingholes. 31Nevermounttheunitnearthefueltank. position"45°" Bracket(L) Bracket(R) Hexagonalboltwithwasherbase(M5x8) Drillholes4mmindiameter. Bracket(R) Self-tappingscrew(M5x12) NOTE:Useseals(A)tocoverunusedmountingholesonsidesofunit. Bracket(L) VEHICLE WIRING Mating 8-pin DIN socket on rear of compatible radio chassis (see note 1 below). DIN cable(8-pin) CD changer Car Stereo with CD Changer Controls NOTE: 1. Check with your Audiovox car audio...