Votes - 2, Average rating: 4 ( )

Manafacture: Alpine File size: 580.42 kb File name: Language of manual:

Unable to fast forward or backward the CD. • The CD has been damaged. -Eject the CD and discard it; using a damaged CD in your unit can cause damage to the mechanism. CD playback sound skips due to vibration. • Improper mounting of the unit. -Securely re-mount the unit. • Disc is very dirty. -Clean the disc. • Disc has scratches. -Change the disc. • The pick-up lens is dirty. -Do not use a commercial available lens cleaner disc. Consult your nearest ALPINE dealer. CD playback sound skips without vibration. • Dirty or scratched disc. -Clean the disc; damaged disc should be replaced. Error displays (built-in CD player only) • Mechanical error -Press the c button. After the error indication disappears, insert the disc again. If the above- mentioned solution does not solve the problem, consult your nearest ALPINE dealer. Indication for CD HI TEMP • Protective circuit is activated due to high temperature. -The indicator will disappear when the temperature returns to within operation range. ERROR • Mechanism error. 1. Press the c button and eject the CD. If not ejecting, consult your Alpine dealer. 2. When the error indication remains after ejecting, press the c button again. If the error indication still does not turn off after pressing the c button for a few times, consult your Alpine dealer. Note When the "ERROR" is displayed: In case that the disc cannot be ejected by pressing the c button, press the Reset switch (refer to page 4) and press the c button again. If not ejecting, consult your Alpine dealer. T–– ––– • No CD is inserted. -Insert a CD. Indication for CD Changer HI TEMP • Protective circuit is activated due to high temperature. -The indicator will disappear when the temperature returns to within operation range. ERROR - 01 • Malfunction in the CD Changer. -Consult your Alpine dealer. Press the magazine eject button and pull out the magazine. Check the indication. Insert the magazine again. If the magazine cannot be pulled out, consult your Alpine dealer. • Magazine ejection not possible. -Press the magazine eject button. If the magazine does not eject, consult your Alpine dealer. ERROR - 02 • A disc is left inside the CD Changer. -Press the Eject button to activate the eject function. When the CD Changer finishes the eject function, insert an empty CD magazine into the CD Changer to receive the disc left inside the CD Changer. NO MAGZN • No magazine is loaded into the CD Changer. -Insert a magazine. NO DISC • No indicated disc. -Choose another disc. Specifications FM TUNER SECTION Tuning Range 87.5 – 108.0 MHz Mono Usable Sensitivity 0.7 .V Alternate Channel Selectivity 80 dB Signal-to-Noise Ratio Stereo Separation 65 dB 35 dB MW TUNER SECTION Tuning Range Sensitivity (IEC Standard) 531 – 1,602 kHz 25.1 .V/28 dB LW TUNER SECTION Tuning Range Sensitivity (IEC Standard) 153 – 281 kHz 31.6 .V/30 dB CD SECTION Frequency Response Wow & Flutter (% WRMS) Total Harmonic Distortion Dynamic Range Signal-to-Noise Ratio Channel Separation 5 – 20,000 Hz (±1 dB) Below measurable limits 0.008% (at 1 kHz) 95 dB (at 1 kHz) 105 dB 85 dB (at 1 kHz) GENERAL Power Requirement Maximum Power Output Output Voltage Bass Treble Weight 14.4 V DC (11–16 V allowable) 45 W . 4 2 V/10k ohms ±14 dB at 60 Hz ±14 dB at 10 kHz 1.5 kg (3 lbs. 5 oz) CHASSIS SIZE Width Height Depth 178 mm (7") 50 mm (2") 155 mm (6-1/8") NOSEPIECE SIZE Width Height Depth 170 mm (6–3/4") 46 mm (1-13/16") 18 mm (11/16") Due to continuous product improvement, specifications and design are subject to change without notice. 17-EN Installation and Connections Before installing or connecting the unit, please read the following and pages 2 and 3 of this manual thoroughly for proper use. Warning MAKE THE CORRECT CONNECTIONS. Failure to make the proper connections may result in fire or product damage. USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND. (Check with your dealer if you are not sure.) Failure to do so may result in fire, etc. BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL. Failure to do so may result in electric shock or injury due to electrical shorts. DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS. Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, gear lever, brake pedals, etc. can be extremely hazardous. DO NOT SPLICE INTO ELECTRICAL CABLES. Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock. DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES. When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire. DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. Bolts or nuts used for the brake or steerin...

Download now

Please, enter two numbers from picture: