Votes - 3, Average rating: 3
(
)
)
|
manual abstract
To check the specified time and source Press the TIMER button. The timer-on time, the selected source name and the duration for the timer-activated period are displayed for 4 seconds. To cancel timer standby mode temporarily Press the TIMER button repeatedly so that 0 or OREC disappears on the display. To restore the timer standby mode, press again to display @l or OREC. Using the unit while the timer is set You can use the unit normally after setting the timer. Before ‘turning off the power, repeat step 5 to prepare the source, and adjust the volume and tone. m: Timer playback and timer recording will not begin unless the power is turned off. Connected equipment cannot be turned on and off by the built- in timer of this unit. Use an external timer, T[MER RECORDING Timer recording is applicable for TUNER and VI DEO/AUX (with an external timer) sources only. Press the TIMER button repeatedly until @REC appears on the display, and press the 11 SET button within 4 seconds. Carry cwt the steps of “SETTING THE TIMER” from step 2 and insert the tape to be recorded into deck 2 after step 5. SETTING THE SLEEP TIMER ~ 1 2 The unit can be turned off automatically at a specified time, Use the remote control, 1 Press the SLEEP button. 2 Within 4 seconds, press the -or -button to specify the time until the power is turned oft. Each time the button is pressed, the time changes between 5 and 240 minutes in 5-minute steps. m Specified time To check the time remaining until the power is turne(d off Press the SLEEP button once. The remaining time is displayed for 4 seconds. To cancel the sleep timer Press the SLEEP button twice so that “SLEEP” on the display disappears. ENGLISH ~! 2 CONNECTING OPTIONAL LISTENING TO EXTERNAL EQUIPMENT SOURCES — CD DIGITAL OUT (OPTICAL) — VIDEO/AUX — MD —LINEOUT Refer to the operating instructions of the connected equipment for details. The connecting cords are not supplied. Obtain the necessary connecting cords. Consult your local Aiwa dealer for optional equipment. VIDEWAUX, MD JACKS This unit can input analog sound signals through these jacks. Use a cable with RCA phono plugs to connect audio equipment (turntables, LD piayers, MD players, VCRs, TV, etc.). Connect the red plug to the R jack, and Ihe white plug to the L jack. When connecting a turntable Use an Aiwa turntable equipped with a built-in equalizer amplifier. LINE OUT JACKS This unit can output analog sound signal through these jacks. Use a cable with RCA phono plugs to connect audio equipment with LINE IN (analog input) jacks. m Do not connect an equipment to the LINE OUT terminals and VI DEO/AUX terminals simultaneously. Otherwise, noise is generated and malfunction occurs. CD DIGITAL OUT (OPTICAL) JACK This unit can output CD digital sound signals through this jack. Use an optical cable to connect digital audio equipment (digital amplifier, DAT deck, MD recorder, etc.). Remove the dust cap @ from the CD DIGITAL OUT (OPTICAL) jack. Then, connect an optical cable plug to the CD DIGITAL OUT (OPTICAL) jack. POWER To play equipment connected to the VIDEO/AUX jacks or MD jacks, proceed as follows. 1 Press the VIDEO/AUX or MD button. When a equipment connected to the VIDEO/AUX jacks is played: press the VIDEO/AUX button. When a equipment connected to the MD jacks is played: press the MD button. 2 Play the connected equipment. To change a source name in the display When the VIDEO/AUX button is pressed, VIDEO is displayed initially. It can be changed to AUX or TV. With the power on, press the POWER button while pressing the VIDEO/AUX button. Repeat the procedure to select one of the names. To adjust the sound level of the external source When the sound level of the external source is much higher or much lower than that of other function sources, adjust it as follows. 1 Press the VI DEO/AUX or MD button and play the equipment. 2 Presss the < or > button so that the sound level becomes the same as that of other function sources. m During recording, the sound level can not be adjusted. When the CD DIGITAL OUT (OPTICAL) jack is not being used Attach the supplied dust cap. 23 ENGLISH CARE AND MAINTENANCE TROUBLESHOOTING GUIDE Occasional care and maintenance of the unit and the software are needed to optimize the performance of your unit. To clean the cabinet Use a soft and dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with mild detergent solution. Do not use strong solvents, such as alcohol, benzine or thinner as these could damage the finish of the unit. To clean the heads and tape paths After every 10 hours of use, clean the heads and tape paths with a [head cleaning cassette or cotton swab moistened with cleaning fluid or denatured alcohol. (These cleaning kits are commercially available.) When cleaning with a cotton swab, wipe the recording/playback head, erasure head (deck 2 only), capstans, and pinchrollers. I Playback :ead Cotton swab 1 1 Pinchroller Erasure head P;nchroller After cleaning the heads...