Votes - 4, Average rating: 4.3
(
)
)
|
manual abstract
11 HD8000_022004.p65 11 20/2/2004, 12:22 REPEAT PLAYBACK The player can be programmed to continuously repeat a single track or the entire disc automatically. One Track Repeat During playback press the SKIP FWD or SKIP REV buttons to select the track to be repeated, then press the REPEAT/INTRO button once. The indicator appears in the display and the selected track will be repeated continuously. Press the STOP button to cancel Repeat 1 playback. All Tracks Repeat Press the PLAY/PAUSE button to begin playback, then press the REPEAT/INTRO button twice. The ALL indicator will appear in the display and the entire disc will be repeated continuously. Press the STOP button to cancel All Track Repeat playback. 12 HD8000_022004.p65 12 20/2/2004, 12:22 INTRO (Intro Scan) PLAYBACK The Intro Scan feature plays only the first 10 seconds of each track on the disc. This feature is useful when you are trying to find a particular song but you cannot remember the title. 1.) Load your disc in the player as usual and press the PLAY/PAUSE button to begin playback. 2.) When playback begins press the REPEAT/ INTRO button 3 times. The INTRO indicator flashes. 3.) Press the PLAY/PAUSE button once more. The INTRO indicator stops flashing and remains ‘On’. The player backs up to the beginning of track 1, plays the first 10 seconds of each track on the disc, and then stops. To cancel Intro Scan playback press the STOP button. RANDOM (Shuffle) PLAYBACK When Random playback is selected all the tracks on the disc will be played back in random order. 1.) Load your disc in the player as usual and press the PLAY/PAUSE button to begin playback. 2.) When playback begins press the RANDOM button. The SHUFF indicator flashes. 3.) Press the PLAY/PAUSE button once more. The SHUFF indicator stops flashing and remains ‘On’. The player randomly selects a track for playback. After each track has played once the player stops. To cancel Random playback press the STOP button. 13 HD8000_022004.p65 13 20/2/2004, 12:22 PROGRAMMED PLAYBACK You can program up to 20 tracks on a disc to play in any desired order. NOTE: You can program a disc either during playback or in Stop mode. 1.) Press the PROG button once. The PROG indicator and the Program Number ‘01’ appear, and the track number ‘00’ flashes. 2.) Press the SKIP FWD or SKIP REV button to select the first track to be programmed. Example: Track 2. 3.) When the desired track number is flashing in the display press the PROG button again to enter the desired track number in Program Number 1. The track number returns to “00” and the Program Number advances to “02”. 4.) Repeat Steps 2 and 3 to program additional tracks up to a maximum of 20. 5.) Press the PLAY/PAUSE button to begin programmed playback. The PROG indicator remains in the display and the track display stops flashing. • Playback begins with the first track you programmed and continues until all programmed tracks have been played, and then the player stops. The programmed sequence will remain in the memory until the power shuts off (approximately 30 seconds) or until the CD door is opened. • If you press the PROG and PLAY/PAUSE buttons again before the power shuts off the programmed sequence will play again. 14 HD8000_022004.p65 14 20/2/2004, 12:22 IMPORTANT! RESETTING THE SYSTEM MEMORY If this player is subject to a severe electric shock or a repeated, intentional series of incorrect key commands, the system memory may “freeze” and the player will not respond to any further key commands. If you find that the player is not responding when you operate the controls, first make sure that the batteries are not dead. If the batteries are OK, open the CD door for 10 seconds, re-close it, and try the operation again. If the player still fails to respond, remove the batteries from the unit, wait at least one minute for the system memory to clear, and then re-install the batteries. 15 HD8000_022004.p65 15 20/2/2004, 12:22 CARE AND MAINTENANCE CARE AND MAINTENANCE CLEANING THE CABINET Wipe with a soft cloth. If the cabinet is very dirty, dampen the cloth with a weak solution of neutral detergent and water, and then wipe clean. CLEANING THE LENS A dirty lens will cause sound skipping and, if the lens is very dirty, the CD may not work. Open the disc cover and clean the lens as follows: DUST OR DRY PARTICLES Using a camera lens brush/blower, blow on the lens several times, then wipe it lightly with the brush to remove dust. Then, blow on the lens once more. FINGERPRINTS To remove fingerprints from the lens, use a cotton swab starting in the middle and working to the outside edge. Use only very light pressure on the lens to avoid forcing it out of alignment. CLEANING THE DISC When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center out. NOTE: Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended for analog discs. 16 HD8000_022004.p65 16 20/2/2004, 12:22 LIMITED WARRANTY Emerson ...