Votes - 5, Average rating: 4 ( )

Manafacture: Samsung File size: 292.06 kb File name: Language of manual:

1 1 2 3 4 5 Digital output terminal You can connect a sound card or MPEG card which support Digital output terminal to your drive using this two-pin terminal. 1 Turn OFF your computer. Remember to verify the configuration jumper on the rear of the CD-ROM drive. 2 Remove the cover of your PC(main unit of the computer) 3 Remove the blank cover panel of the 5.25 inch unit in which the CD-ROM drive is to be installed. 6 Put the cover back on your PC. 5 Install the CD-ROM drive into the unit and secure it with mounting screws (recommended standard M3x6x4) . Depending on your PC model, you may need to attach guide rails to the drive, so that the drive is held firmly in place. . If you use screws that are longer than the recommended standard, you may damage the drive. Before you install the CD-ROM drive, we strongly recommend that you make certain that your set-up meets the system requirements listed below. Installing the CD-ROM Drive Install the CD-ROM drive in your computer horizontally, making sure that the Open/Close button is on the right. To install the drive, proceed as follows. 2 Sound output terminal You can connect a sound card to your drive using this four-pin terminal. . This function is not covered in detail in this guide. Refer to the documentation supplied with your sound card. 3 Master/slave select terminal Usually, this is a pre-set configuration as illustrated below. . Verify that the setting is as illustrated. If it is not, simply remove the jumper and place it in the correct position. 4 Interface terminal This input/output interface terminal is used to connect the 40-pin flat cable from the IDE interface to the CD-ROM drive. 5 Power terminal The power terminal is a four-conductor male plug. Eject Button 4 Disc compartment The compartment opens and closes automatically when you press the Eject button. Emergency eject hole If the compartment does not open when you press the Eject button, power off the computer, insert a pin or unfolded paper clip in the hole and push firmlhy) 6 5 2 Headphone volume control This headphone volume control adjusts the volume for your headphones. You can only use the headphone jack and volume control when you have installed the required software utilities. For example, the Microsoft Windows Media player can be used. 3 LED 4 Connect the CD-ROM drive to the IDE interface and power cables Iocated inside your computer. . Connectors are keyed so it is impossible to put them in an incorrect position. Do not force the connectors, if they do not seem to fit. Item Windows version MS-DOS version Disk space Free expansion unit Type of computer Description Windows 95/98/2000/ME/XP Windows NT 4.0(or higher) 5.0(or higher) 100KB minimum 5.25 inch IBM 486SX 20MHz (or higher) with an IDE interface(or a 100% IBM-compatible computer) CD-ROM DRIVE SC-152 User's Guide - ENGLISH Technical Specifications Max. 7800KB/s SECTIONS SC-152N DISC DRIVE PER - FORMANCE FRONT PANEL REAR PANEL OPERATING ENVIRONMENT GENERAL RELIABILITY ERROR RATE Disc types supported Disc diameter Data transfer rate Access time (1/3 stroke) Data buffer capacity Laser Slide mechanism Spindle motor Load mechanism Button Indicator(LED) Headphone output Volume control Required power Interface connector Audio output Jumper block Work area Storage area Dimensions (W x H x D) Net weight MTBF CD-DA, CD-ROM Mode-1, CD-ROM XA Mode-2 Form-1, Form-2, CD-Plus, CD-Extra, Photo-CD(Single, Multi-session), Video CD ready, Enhanced CD, CD-I/Fmv, CD-R/RW 120mm or 80mm PIO Mode - 4. DMA MW2, Ultra DMA(option) 75ms(typical) 128KB Semiconductor Laser Gear motor Brushless motor Tray, DC motor(Soft Eject) Mode-1 : 1block / 10 bits, Mode-2 : 1 block/10 bits Eject(Open/Close) Busy Stereo Mini - jack (O 3,6 mm) 0.60 ± 20% (Vrms) 33. Dial type +5V DC 1.3A, +12V DC 1.5A ATAPI Line out 0.70 ± 20%(Vrms), 47k. Device configuration jumper Temperature : 5~45 °C, Humidity : 8~80% Temperature : -40~60 °C, Humidity : 5~90% 900g (set only) 125,000 POH(Duty 20%) 146mm(W) x 44.5mm(H) x 202(D)mm SAMSUNG continually strives to improve its products. Both the design specifications and these user instructions are thus subject to change without notice. 12 9 BG68-00326A Ver : 03 Safety Precautions The following diagrams illustrate the precautions to be taken when using your CD-ROM drive. Setting Up the Device Driver It is not necessary to set up additional device driver for Window 95/98/2000/NT because it uses the device driver provided by the Window. Solving Technical Problems . Frictional sound detected during the operation of Spin-Up and Stop is made ABS (Auto Balance System), not by malfunction. Automatic Setup Manual Setup LAST DRIVE = Z - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - DEVICE = C :\SAMSUNG\SSCDROM.SYS /D : SSCD000 /V - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ...

Download now

Please, enter two numbers from picture: