Votes - 4, Average rating: 4.3
(
)
)
|
manual abstract
Preferably, connect a second E-IDE cable to the CD-R/RW drive in master mode; see page 7 for further details. ♦ Check the position of the jumper in the master/slave select terminal. The CD-R/RW drive is not recognized by MS-DOS. ♦ Reinstall the device driver or update it with the latest version by downloading it from the Samsung Web site. The CD-R/RW drive is not detected by Wndows. ♦ This case may occur when there is a Windows installation problem; reinstall Windows. No sound is heard from an audio CD. ♦ Check whether the audio cable is correctly connected to the sound output terminal on the CD-R/RW drive and the sound card CD-IN terminal. ♦ Check that the sound card is operational. ♦ Adjust the volume control. ♦ Run the CD player supplied with Windows or your sound card. You can listen to the CD by connecting headphones to the appropriate connector. If you have installed the appropriate player, such as Microsoft Wndows Media Player, you can adjust the volume using the headphone volume control on the drive front panel. ♦ If you select DIGITAL at CD Audio Play in Media Player of Wndows ME/XP, the earphone does not appear in the Digital Mode. A CD is not read or is read too slowly. ♦ Check whether the CD is of good quality and clean it, if necessary. The disc compartment will not open. ♦ Check that the power cable is correctly connected. ♦ Power off and disconnect the PC. Insert a pin or unfolded paper clip in the emergency hole and push firmly until the disc compartment opens. When the MPEG software plays a Video CD, the pictures are not regular and the running speed is too slow. ♦ Adjust the size of the replay screen. ♦ After checking the display resolution, adjust it, if necessary. The Disc is not in message is displayed even though a disc has been inserted. ♦ The computer may not recognize the disc if you start playback too quickly after inserting the disc. Open and close the disc compartment and try again. ♦ Clean the disc and try again. The CD-R/RW drive is not detected after it is connected to a sound card. ♦ The interface mode of the sound card is AT-BUS. You must therefore connect the CD-R/RW drive to the E-IDE port on the PC mother board, rather than to the sound card, or install an E-IDE-compatible sound card. Problem Meaning / Solution IN CD has the Formatted Disc Eject function. ♦ Right-click the mouse on TRAY ICON (right side of the menu bar at the bottom of the monitor) and then select "Eject1 to take the CD out. ♦ Select the drive where the disc is inserted from Windows Explorer. Right-click the mouse and select "Eject1 to take the CD out. When recording NERO, it will be recorded not on a CD but a form of image file. ♦ This seems to occur when you select the recording function as the system selects "Image Recorder" instead of SW-224. In this case, select a recorder from the menu items at the upper part of NERO and then select SW-224 from the Recorder Selection window. ♦ When installing the recording software, try not to install the software before the ROM drive as this makes the Image Recorder selected. The Recorder cannot recognize the disc. ♦ Use the firmware automatic upgrade function available at the ODD service website to download the newest firmware and then reinstall the recording software which is included in the bundle. - - SW-224_eng-02 12/19/01 4:42 Pjd-^Page 18 Technical Specifications SAMSUNG continually strives to improve its products. Both the design specifications and these user instructions are thus subject to change without notice. Item SW-224 Disc Disc types supported in read mode CD-DA, CD-ROM mode 1, CD-ROM XA mode 2, Form 1, Form 2, CD-Plus, CD-Extra, Photo-CD (Single, Multi-session), Video CD ready, Enhanced CD, CD-I/FMV, CD-R, CD-RW, CD-TEXT Disc types supported in write mode CD-R, CD-RW Erasing disc types CD-RW Disc diameter 120 mm or 80 mm Drive Performance Data transfer rate CD-R (write mode) 600 KB/sec. (4X), 1 200 KB/sec. (8X) 1800 KB/sec. (12X), 2400 KB/sec. (16X) 3000 KB/sec. (20X), 3600 KB/sec. (24X) CD-RW (write mode) 600 KB/sec. (4X), 1500 KB/sec. (10X) Read mode 6,000 KB/sec. (max.), PIO Mode 4, DMA Mode 2 Access time (typical) 90ms (typical) Laser Semiconductor laser Slide mechanism Stepping motor Spindle motor Brush less motor Load mechanism Tray. DC motor (Soft Eject). Error rate Mode 1: 1 block/1012, Mode 2: 1 block/109 Front Panel Eject button Auto eject or Auto inject Indicator (LED) Green when playing or recording a disc Headphone output Stereo mini-jack (0 3.6 mm) 0.60±20% (vrms) 33 Q Volume control Dial type Rear Panel Required power +5 VDC: 1.5 A (max.), +12 VDC: 1.5 A (max.) Interface connector ATAPI (ElDE) Audio output Line out 0.75 ± 20% (vrms): 47 KQ Jumper block Device configuration jumper Operating Environment Operations Temperature: 0~50°C Humidity: 10-80% Storage Temperature: -25~55°C Humidity: 10-9...