Connecting the Wireless Subwoofer The Subwoofer's linking ID is preset at the factory and the main unit and sub should link (connect wirelessly) automatically when turned on. If the link indicator does not light when main unit and subwoofer are turned on, please set the ID by following the process below. 1 . Plug the power cords of the main unit and subwoofer into the AC power supply. 2 . Press the ID SET button on the back of the subwoofer with a small, pointed object for 3 seconds. • The STANDBY indicator is turned off and the LINK indicator (blue LED) blinks quickly. 03 Connections ID SET ID SET 3 . In stand-by mode while the main unit is off, press the 0, 1, 3, 5 buttons in order. • The red standby LED on main unit flashes and then stop in few second. 4 . Press the POWER button to turn on the main unit. • The main unit and the subwoofer are now linked (connected). • The Link indicator (blue LED) on the subwoofer is turned on. | NOTE | . Before moving or installing the product, be sure to turn off the power and disconnect the power cord. . If the main unit is powered off, the wireless subwoofer will be in the standby mode and the STANDBY LED on the upper side will blink. . If the main unit doesn't make wireless connection, follow steps 1-4 above to retry the connection between the main unit and wireless subwoofer. | CAUTION | . The wireless receiving antenna is built into the wireless subwoofer. Keep the unit away from water and moisture. . For optimal listening performance, make sure that the area around the wireless subwoofer location is clear of any obstructions. English 15| HT-E8200_XU_0315.indd 15 2012-03-15 .. 1:10:30 Connections Connections Attaching the Toroidal Ferrite Core to the Power Cord If you attach a Toroidal ferrite core to the power cord, it will help to prevent RF interference from radio signals. ID SET 1. Pull the fixing tab of the Toroidal ferrite core to open it. 2. Make a loop twice in the power cord. 3. Attach the Toroidal ferrite core to the power cord as the figure shows and press it until it clicks. Connecting the FM Antenna 1 . Connect the FM antenna supplied tothe FM ANT Jack. 2 . Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall or other rigid surface. | NOTE | . This product does not receive AM broadcasts. HDMI OUT HDM HDMI IN 2 LAN VIDEO OPTICAL INFM ANT FM Antenna (supplied) Installing the Cradle Stand 1 . Put the 3 bumps on the product into the three holes on the cradle stand. 2 . Put the supplied a screw in the product and rotate them clockwise with screw driver. Screw 3 bumps | 16 English 1 HT-E8200_XU_0315.indd 16 2012-03-15 .. 1:10:32 Installing the Wall Mount You can use the wall mount bracket to mount this unit on a wall. Installation Precautions • Do not install on a place other than a vertical wall. • For the installation, avoid a location with high temperature or humidity. • Check the strength of the wall. If the strength of the wall is insufficient for the product installation, make sure to reinforce the wall before the installation. • Check the material of the wall. If the wall is made of plaster board, marble, or iron board, purchase and use the appropriate fixing screws. • Cables connecting to external devices need to be connected to the set before installing. • Be sure to turn off and unplug the unit before installation. Otherwise, it may cause electric shock. 1 . Rotate a screw on the cradle stand counter2 . clockwise to seperate them from the unit. Place the wall mount bracket on a wall surface and then secure it with two screws (not supplied). Be sure to install the wall mount bracket so that the arrow ( ) is placed in the centre of the TV. 3 . Then, fit the unit into the corresponding slots of the wall mount bracket. For secure installation, make sure the mounting studs slide firmly down into the bottom of the slots. 4 . This is the completion of the suggested wall mountinstallation. | NOTE | . Do not hang onto the installed unit and avoid any impact to theunit. . When the unit is installed on a wall, please make sure that a child does not pull any of connecting cables, as it may cause it to fall. . When you install the product with TV on the wall, leave sufficient space for ejecting a CD. (Disc size 12cm+ space for moving hands) 1 2 213 4 03 Connections English 17| HT-E8200_XU_0315.indd 17 2012-03-15 .. 1:10:35 Connections Connections Connecting to a TV Select either Method 1 or Method 2. • If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote control, and then select the correct external source from the TV's source list (HDMI, Video In, etc.) to view video from the home Cinema. HDMI INVIDEO IN Method 2 (Cable not supplied.) Method 1 Method 1 Connecting to a TV with a Video Cable - Good Quality Connect the supplied Video cable from the VIDEO OUT jack on the back ...
)
