Votes - 3, Average rating: 5
(
)
)
|
manual abstract
.When set to “On”, the internal control unit will be powered and the idle power consumption will increase compared to when set to “Off”. (About the power consumption • 32) . Remote Control Code Change the remote control code if other Panasonic products react to this remote control. . Firmware Update (• 13) Press [OK] to show the following settings: ..Automatic Update Check When this equipment remains connected to the Internet, it will check for the latest firmware version when it is turned on and you can update it if necessary. ..Update Now You can update the firmware manually if a firmware update is available. . System Information Press [OK] to show the following settings: ..License Information about the software used by this unit is displayed. ..Firmware Version Information Display firmware version of this unit and wireless LAN module. . Restore Default Settings This returns all values in the Setup menu and the Option menu to the default settings, except for some settings of network, ratings, remote control code, language, etc. 26 VQT3V18 Troubleshooting guide Before requesting service, please perform the following steps. Do you have the latest firmware installed? Firmware updates may be released to correct operating irregularities that are discovered with certain movies. (..13) 4Make the following checks and visit our website for more information. For U.S.A. : Enter the model number. For Canada : 4Or visit our website to find a service center. You can find a service center near you easily on our website. Other support information: “Customer Services Directory (United States and Puerto Rico)” (..37) or “Limited Warranty (Only for CANADA)” (..38). The following do not indicate a problem with this unit: – Regular disc rotating sounds. – Image disturbance during search. . Unit doesn’t respond to remote control or front panel buttons. Disconnect the power cord, wait 1 minute, then reconnect the power cord. . Cannot eject disc. The unit may have a problem. 1 While the unit is on, press and hold [OK], [B] and [Y] on the remote control at the same time for more than 5 seconds. – “00rEt” is displayed on the unit’s display. 2 Repeatedly press [1] (right) on the remote control or [I/I] on the unit until “06FtO” is displayed on the unit’s display. 3 Press [OK] on the remote control or [< OPEN/CLOSE] on the unit. General operation To return to the factory preset. • Select “Yes” in “Restore Default Settings” in the Setup menu. (• 26) To return all settings to the factory preset. • Reset the unit as follows: 1 While the unit is on, press and hold [OK], [B] and [Y] on the remote control at the same time for more than 5 seconds. – “00rEt” is displayed on the unit’s display. 2 Repeatedly press [1] (right) on the remote control or [I/I] on the unit until “08FIn” is displayed on the unit’s display. 3 Press and hold [OK] on the remote control or [< OPEN/CLOSE] on the unit for at least 5 seconds. The remote control doesn’t work properly. • Change the batteries in the remote control. (• 4) • The remote control and main unit are using different codes. If “SEt .” is displayed on the unit’s display when a button is pressed on the remote control, change the code on the remote control. (• 26, 30) The TV tuner mode is not displayed when the TV is switched on. • This phenomenon may occur, depending on the TV setting, when “Quick Start” is set to “On”. • Depending on the TV, this phenomenon may be prevented by reconnecting the HDMI cable to a different HDMI input terminal or by changing the HDMI auto connection setting. You have forgotten your ratings password. You want to cancel the ratings level. • The ratings level returns to the factory preset. 1 While the unit is on, press and hold [OK], [B] and [Y] on the remote control at the same time for more than 5 seconds. – “00rEt” is displayed on the unit’s display. 2 Repeatedly press [1] (right) on the remote control or [I/I] on the unit until “03VL” is displayed on the unit’s display. 3 Press [OK] on the remote control or [< OPEN/CLOSE] on the unit. Reference Settings VQT3V18 27 This unit does not recognize the USB connection correctly. • Disconnect and reconnect the USB cable. If it still does not recognize the connection, turn the power of this unit off and on again. • USB devices may not be recognized by this unit when connected using the following : – a USB hub – a USB extension cable other than the supplied with the Wireless LAN Adaptor DY-WL5 (optional) • If you connect USB HDD to this unit, use the USB cable that is supplied with the HDD. The unit switches to standby mode. • This unit will automatically turn to standby mode after 30 minutes if it is inactive. (• 16) • One of the unit’s safety devices is activated (U59 is displayed). Wait until this unit has cooled down. Picture The images from this unit do not appear on the television. Picture is distorted. • An incorrect resolution is selected in “HDMI Resolution”. Reset the setting...