Votes - 4, Average rating: 4
(
)
)
|
manual abstract
to a mixture. 12 Use of mixing bowl with whipping whisk Before beginning to attach this or any other attachment, make sure that the power unit is on a smooth, clean, suitable work surface and switched to the Off position, “O/Off,” and that you have the safety motor drive cover in place of the high speed, blender drive. 1. Before using the mixing bowl and whipping whisk for the first time they should be washed. See Before Using for the First Time, on page 4. Figure 7. The whipping whisk, supplied with the MCM 5200 UC, may be removed from its holder as shown in figure 7, and washed in the dishwasher along with the mixing bowl and other components. After washing, rinse well and dry the whisk and whisk holder before reattaching the whisk. 2. Make sure the safety motor drive cover has been snapped into place on the high-speed blender drive. Place the mixing bowl on the dual drive of the power unit, as shown in figure 4a, and turn the bowl clockwise with a slight downward pressure until bowl is firmly seated. 3. Engage the whipping whisk on the dual drive of the power unit by placing it over the center column, as shown in figure 8. Once in place, check to make sure the whipping whisk has engaged the dual drive by turning the whipping whisk counterclockwise while pushing down until it stops. Figure 8. 4. Next place the mixing bowl cover on the bowl. Make sure arrows on cover and bowl are aligned, so that tabs on bowl fit into channels in cover and then turn cover clockwise until tab on cover enters cover interlock and turn until tab clicks into place, The cover should be in place whenever the power unit is in operation. The cover serves to prevent the escape of flour dust at the beginning of the stirring process, and also serves to prevent accidental contact with the moving whipping whisk. Also, the power unit will not operate unless the tab on the cover is in place and has engaged the safety cover interlock. 13 Placing into Operation with Whipping Whisk Make sure that the power unit is on a smooth, clean, suitable work surface and switched to the Off position, “O/Off.” Pull the electrical cord out to the necessary length and plug into a convenient outlet. The mixing bowl with whipping whisk is now ready for operation. Sample recipes may be found in the recipe section, at the back of this manual. Mixing bowl tips: 1. When using the mixing bowl to knead or mix a recipe designed to be prepared by hand, you will find that with the Bosch Food Processor you can usually place all the ingredients in the mixing bowl at once. When doing this, always place the liquids in first. This will assure more thorough mixing. 2. When adding ingredients to a mixture: a. Turn the rotary switch to a lower speed b. Remove the pusher/measuring cup c. Add the ingredients through the feed tube and replace the pusher/measuring cup. 3. If a large batch of dough is to be left in the mixing bowl and allowed to rise, the cover should be removed and placed loosely on the bowl so that it is free to move if the dough should begin to press on it. How to Use Slicing and Grating Discs All the MCM models comes with the mixing bowl, cover and pusher/measuring cup and reversible slicing disc and reversible coarse grating disc, see figures 5h and 5i. The MCM 5200 also comes with a fine grating disc, as shown in figure 5g. The slicing disc and the grating discs are intended to be used for slicing and/or grating of vegetables, as well slicing/grating of soft cheeses and sausages or meat and grating of vegetables and hard cheese. WARNING 1. Blades on discs are sharp. Handle carefully. Always use the center plastic holder to lift or handle discs. Do not grip the discs by the blades or metal surfaces. 2. When operating using the slicing or grating discs keep hands clear of filling tube. Only work with pusher. 3. Always operate the power unit with the cover in place. Use of mixing bowl with slicing or grating discs Before beginning to attach this or any other attachment, make sure that the power unit is on a smooth, clean, suitable work surface and switched to the Off position, “O/Off,” and that you have the safety motor drive cover in place of the high speed, blender drive. 1. Before using the mixing bowl and slicing or grating discs for the first time they should be washed. See Before Using for the First Time, on page 4. 2. Make sure the safety motor drive cover has been snapped into place on the high-speed blender drive. Place the mixing bowl on the dual drive of the power unit, as shown in figure 4a, and turn the bowl clockwise with a slight downward pressure until bowl is firmly seated. 3. Engage the slicing or grating disc, by picking up the disc you wish to use, with the side you wish to use facing upward, by the plastic holder in the center of the disc and placing over the rectangular shank of the dual drive of the power unit. 14 WARNING The blades on the discs are very sharp. Handle with care. Use center plastic holder when handling discs. 4. Next plac...
Other models in this manual:Blenders - UC MCM 5100 (1.43 mb)
Blenders - UC MCM 5200 (1.43 mb)