Votes - 2, Average rating: 4
(
)
)
|
manual abstract
IMPORTANT : THE PLUG REMOVED FROM THE MAINS LEAD, IF SEVERED, MUST BE DESTROYED AS A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED INTO A LIVE SOCKET OUTLET. Should the fuse in the 13 amp plug require changing a 3 amp BS1362 fuse must be fitted 2 Features FeaturesFeaturesFeaturesFeaturesFeatures Speed control dial Pulse operation button Base assembly Drive shaft Cover safety interlock Processing bowl Cover Feeder tube Food pusher Large citrus press Small citrus press Citrus strainer Citrus press drive gear Citrus press support post Chopping blade Unpacking and using your machine for the first time. Carefully unpack you new processor attachments, checking them against the illustrations below. Remove any stickers (except for the serial label) and wash all the parts which are safe to immerse in water. Never immerse the processor body in water or any other liquid. It may be wiped over with a clean, damp cloth - but only when unplugged from the electrical outlet. Your food processor has two citrus press attachments 1 To separate the citrus press attachments press the release button on both sides of the large citrus press. 2 Gently pull the attachments apart. 18 19 20 Dough blade Plate holding disk 18 Grating plate 19 Slicing plate 20 Spatula 3 Operating controls Operating controlsOperating controlsOperating controlsOperating controlsOperating controls The food processor control knob has three settings: O = Off I = Low speed II = High speed The compact food processor has a variable speed control dial which can be set to either low speed when less power is needed or high speed if full power is required. The speed selector can be adjusted whilst the processor is in use. Pulse allows greater control over the texture of the food produced. To operate simply press the pulse button until the food has reached the desired texture. Food processor Food processorFood processorFood processorFood processorFood processor Setting up Using the following instructions, assemble the food processor as follows. 1 Drop the processing bowl onto the base assembly by rotating the bowl clockwise until you hear a click. Ensure that all three interlocks on the bowl engage with the base unit. 2 The blades and disc holder can now be placed into the bowl. Refer to ‘fitting and using the tools’ section which follows. Place food into the processor. 4 Position the food pusher into the feed tube if required. 5 Before plugging the processor in ensure that the bowl and cover are fitted correctly. (The machine will not operate if the assembly is incorrect). 6 Select the desired speed using the speed control dial . Fitting and using Fitting and usingFitting and usingFitting and usingFitting and usingFitting and using the tools the toolsthe toolsthe toolsthe toolsthe tools All tools which are fitted within the processor bowl must be firmly connected to the hexagonal drive shaft in the centre of the processor bowl. Always adjust the tools until you are sure that they are correctly fitted. Metal and plastic blades 1 With the processor bowl already fitted, place the blade over the hexagonal drive shaft of the processor. Lightly turn the tool until it engages onto the drive and the blades are close to the bottom of the bowl and level. 2 Holding the cover by the feed tube, fit the Safety interlock cover by rotating 3 Holding the cover by the feed clockwise. tube, fit the cover Ensure that the by rotating safety interlock clockwise firmly has clicked into until the cover, place. bowl and the base unit interlock. Safety interlock 4 Slicing, and grating plates 1 With the processor bowl already fitted, place the slicing or grating plates into the plate holding disc. The plates should be placed into the disc as shown and clicked into place. (will only fit one way) 2 Place the plate holding disc onto the shaft (with the thinner end at the top) onto the central drive shaft of the bowl and check that it is firmly fixed in place. 3 Holding the cover by the feed tube, fit the cover by rotating clockwise. Ensure that the safety interlocks have clicked into place. (see setting up the processor) 4 Plug in the processor. PLEASE NOTE: When using these discs, never introduce the fingers into the feed tube. Always use the food pusher. Using the citrus press Using the citrus pressUsing the citrus pressUsing the citrus pressUsing the citrus pressUsing the citrus press 1 With the empty processor bowl locked in place, drop the strainer into the top of the processor bowl. 2 Turn the strainer clockwise until the strainer locks Safety interlock into the safety interlock. A click will be heard. 3 Drop the citrus press drive gear onto the drive shaft. 4 Drop the small citrus press into the citrus press support post . 5 If the large citrus press is required drop the large citrus press over the small citrus press. 6 Plug in the processor and select the speed required. Dismantling after use 1 Unplug the processor. 2 Remove the processor bowl cover by turning anti-clockwise. 3 Ca...