Votes - 0, Average rating: 0 ( )

Manafacture: Philips File size: 8.64 mb File name: Language of manual:

(Fig. 9) -When you beat egg whites, use a large bowl for the best result. -To prevent splashing, star t at a low speed setting and continue with a higher speed after approx. 1 minute. -When you whip cream, use the beaker to avoid splashing. Note: Do not use the whisk to prepare dough or cake mixture. Detaching the whisk 1 To detach the whisk, press the release button. 2 To detach the coupling unit, pull it from the whisk. potato bar (HR1655 only) The potato bar can be used to mash cooked ingredients such as potatoes, swede and peas. caution -Never use the potato bar to mash ingredients in a pan over direct heat. Always remove the pan from the heat and allow the ingredients to cool slightly before you star t mashing them. -Do not mash hard or uncooked foods, as this may damage the potato bar. -Do not tap the potato bar on the side of the pan during or after mashing. Use a spatula to remove excess food. -Do not process more than 1 batch without interruption. Let the appliance cool down for 5 minutes before you continue processing. 1 Cook and drain the potatoes. 2 Connect the potato bar to the coupling unit by turning it clockwise (“click”) (Fig. 10). 3 Connect the coupling unit to the motor unit (Fig. 11). 4 Plug in the appliance. 5 Place the potato bar in a bowl with ingredients and set the speed ring to 10. 6 Press the on/off button. 7 Move the potato bar up and down for approximately 20 seconds. Continue until the desired result is achieved. Tip:You can enhance the flavour by adding salt, butter or milk. Tip:To get the best results, make sure the pot is not more than half filled. Detaching the potato bar 1 To detach the potato bar, press the release button. (Fig. 12) EnglisH 11 2 3 To remove the paddle from the potato bar turn it clockwise (Fig. 13). To detach the coupling unit from the potato bar turn it counterclockwise (Fig. 14). Note: Always clean the potato bar immediately after use (see chapter ‘Cleaning’ and the cleaning table). milk foamer Connect the milk foamer to the coupling unit. (Fig. 15) Connect the coupling unit to the motor unit (Fig. 16). Plug in the appliance. Heat up the milk to a temperature between 55°C - 65°C/131°F - 149°F. 1 2 3 4 Tip:You will achieve the best results if you use long-life milk with 3.5% fat content. Note: Do not heat up the milk to a temperature beyond 65°C/149°F. Never let the milk boil. Caution: Do not process more than 1 batch without interruption. Let the appliance cool down for 5 minutes before you continue processing. 5 Pour the milk into a tall heat-resistant beaker. 6 Set the speed ring to the highest setting, press the turbo button and froth the milk for approximately 60 seconds. Note: Clean the milk foamer immediately after use (see chapter ‘ Cleaning’ and the cleaning table). Detaching the milk foamer 1 To detach the coupling unit, press the release button (Fig. 17). 2 To detach the milk foamer, pull it off the coupling unit (Fig. 18). 3 To detach the milk foamer cones, pull them off the milk foamer (Fig. 19). cleaning (Fig. 20) Do not immerse the motor unit, the coupling units, and the mini chopper lid (HR1653 only) or the medium chopper lid (HR1655 only) in water or any other liquid, nor rinse it under the tap. Use a moist cloth to clean the motor unit, the coupling units, and the mini chopper lid (HR1653 only) or the medium chopper lid (HR1655 only) (Fig. 21). Unplug the appliance. Press the release button on the motor unit to remove the accessory you have used. Disassemble the accessory. 1 2 3 Note:To clean the potato bar, remove the paddle by turning it clockwise. (Fig. 13) Tip:You can also remove the rubber rings from the chopper bowls for extra thorough cleaning. 4 See the cleaning table for further instructions. Tip: For quick cleaning of the blender bar or the potato bar, pour warm water with some washing-up liquid into the beaker or jar you have used, insert the blender bar or potato bar and let the appliance operate for approx. 10 seconds. storage 1 You can store the motor unit, the blender bar and the whisk in the beaker (Fig. 22). 12 EnglisH ordering accessories If you need to replace an accessor y or want to purchase an additional accessor y, go to your Philips dealer or visit t. If you have problems obtaining accessories, please contact the Philips Consumer Care Centre in your countr y. accessories available Accessory Service code no. Whisk coupling unit 4203 035 95631 Whisk 4203 035 95641 Milk foamer 4203 035 95651 Medium chopper coupling unit 4203 035 95661 Medium chopper bowl 4203 035 95671 Medium chopper blade unit* 4203 035 95681 Medium chopper ice crushing blade* 4203 035 95691 Mini chopper coupling unit 4203 035 95701 Mini chopper bowl 4203 035 95711 Mini chopper blade unit* 4203 035 95721 Oval beaker with lid 4203 035 95741 *Including protection cap Environment -Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. ...

Download now

Please, enter two numbers from picture: