Votes - 1, Average rating: 5
(
)
)
|
manual abstract
The green pilot light confirms that the appliance is properly inserted in the charging unit and that it is being charged. Full charge: ca. 2 hours Fully charged: the pilot light flashes with longer intervals Operation time is ca. 20 minutes (depending on way of usage) After every usage, place the appliance back onto the charging unit for recharging. This will make sure that it is always ready for use with optimum charging conditions. You may as well store the appliance on the charging unit. Even if not in use for a long period of time, the lithium ion batteries implemented maintain their charging level to a large extent. The batteries are protected against deep discharge. A completely discharged appliance has to be charged for at least ca. 15 minutes before it can be used for an application (e.g. soup). Pilot Light Appliance in charging unit (connected to the mains) Charging or operation conditions Green flashing Battery is charging Green flashing (in longer intervals) Battery is fully charged •• • 10 Switch release button (2) pressed down Charging or operation conditions Green Battery is fully charged Red/green flashing Charge sufficient for at least one usage Red Battery is discharged Red Overheating protection active (go to Safety features A Overheat protection) Safety features Switching on the appliance / Switch lock The appliance has a switch lock. To safely switch it on, follow these points: 1 First press the switch release button (2) with your thumb and hold. 2 Then press the On switch (3). During operation, you can stop pressing the switch release button. If the On switch (3) is not pressed within 5 seconds, the appliance cannot be switched on. The pilot light goes off. In order to switch the appliance on, start again with step 1. Overheat protection When the overheat protection feature is active, the appliance turns off and the pilot light shines permanently red. Reason Trouble shooting Blade is blocked 1. Remove motor part 2. Remove the food/ blockage 3. Place the motor part into the charging unit (connected to the mains) for at least 1 second 4. Processing can be continued Appliance is overheated Follow points 1.-4. If the pilot light still shines red when switching on the appliance, place the motor part back into the charging unit and let it cool down for ca. 1 hour. During this time, the pilot light flashes green. • • Auto Off For safety reasons the appliance turns off after 4 minutes of permanent usage. The appliance can be turned directly on again. Using your handblender The handblender is perfectly suited for preparing dips, sauces, soups, mayonnaise and baby food as well as for mixing drinks and milkshakes. a) Remove knife protection at the bottom of the blender shaft by removing the adhesive tape. Insert the motor part (4) into the blender shaft (6) until it locks. b) Introduce the handblender vertically into the vessel, keep the switch release (2) pressed down, then press the On switch (3). c) To remove the blender shaft from the motor part, press push buttons (5). When operating the handblender in hot liquids do not immerse the blender shaft into – or remove it from the liquid while the appliance is switched on. Recipe example: Mayonnaise 200–250 ml oil, 1 egg (yolk and white), 1 tbsp. lemon juice or vinegar, salt and pepper to taste Put all ingredients into the beaker according to the a.m. order. Introduce the handblender to the base of the beaker. After switching on, keep the handblender in this position until the oil emulsifies. Then, without switching off, slowly move it up and down until the mayonnaise is well combined. Using your chopper attachment The chopper is perfectly suited for chopping meat, cheese, onions, herbs, garlic, carrots, walnuts, almonds, prunes etc. N.B.: Do not chop extremely hard food, such as nutmeg, coffee beans and grains. Before chopping ... pre-cut meat, cheese, onions, garlic, carrots, chilis (see processing guide S. 5) remove stalks from herbs, un-shell nuts remove bones, tendons and gristle from meet. • •• 11 Chopping (see picture section A) 1. Carefully remove the plastic cover from the blade (10b). Caution: the blade is very sharp! Always hold it by the upper plastic part. Press the blade onto the centre pin of the chopper jug (10c) until it locks. Always place the chopper jug on the anti-slip base (10d). 2. Place the food in the chopper jug. 3. Put the gear lid (10a) on the chopper jug. 4. Insert the motor part into the gear lid until it locks. 5. Keep the switch release button (2) pressed down and press the ON switch (3) to operate the chopper. During processing, hold the motor part with one hand and the chopper jug with the other. When chopping hard foods, press down the motor part. 6. After use, press buttons to remove the motor part. 7. Then remove the gear lid. 8. Carefully take out the blade. 9. Remove the processed food from the chopper jug. The anti-slip base also serves as an airtight lid for the chopper jug. Shakes, drinks, purees For purees...